Bremma

Relatively new to the club, had the car a couple of months and just had some new wheels fitted to her.
18/9 Front and 18/10 rear.

jayr_

iTrader: (2)

nice, stock height?... what's size tire you running?

Bremma

Nah it's on lower springs but needs to settle slightly on them before it get's a wheel alignment (meant to sag another 5-10 millimeters)
Tyres are 225/40/18 and 235/40/18

celm

hey guys for the rear
on a 18x9.5 +30 with 255/35 tire and stock height, will I have to roll ??

Driftfc3s

iTrader: (11)

Volk Racing TE37's square setup. 18x9.5 +12mm, Advan Neova AD08 235/40 and Nitto NT05 225/40. Rolled fenders. JIC Magic Coilovers with 8K springs. Since this photo was taken (about 5 days ago), the front now sits about one full inch lower to eliminate the "reverse rake".

timeXlost

iTrader: (1)

Rolling lololol

dabigesii

iTrader: (4)

Originally 18x10 +49 all around. 15mm spacer on front so offset is now +34 and 25mm spacer on back so +24. 285/30/18 on the front 295/30/18 on the back.

Desmoj7

You should be clear.

skyy

FastCars

I think those wheels look GREAT even in the picture! What is the offset?

protunedperformance

iTrader: (8)

I have since adjusted the camber a little and the fitment improved. But you get the idea.

protunedperformance

iTrader: (8)

Forgot to add...18x8.5 up front 50 offset, 245 tires. 18x12 in the rear, 335 tire, 0 offset.

negative.one

posted this in the tire thread but figured it might be better here:

can someone give me some advice? I got a set of wheels sitting here: 18x9 +25mm fronts and 18x10.5 +20mm rears. The tires I ordered are 245/35/18, and 285/30/18. I plan on lowering with coilovers to about one finger gap to no wheel gap, maybe tuck a tiny bit of tire. How will these fit? Will I be ok with a fender roll or will I need a fender pull too? The reason for this post is I may sell the tires for some less wide ones and hope the stretch will get me to fit easier and go as low as I'd like to.

32rulz

Anyone knows the size on these setup?
not mine but came across while searching work s1 3p, i remember reading the rear is like 11.5, any info on the offset and tire size??

thx

DC206R

32rulz

anyone?

pakitagn

i dont think you're going to be able to get the rears to tuck if you put a 285 on there

negative.one

even with roll and pull? I sort of thought it would be difficult. Maybe I should sell the 285's and get some 255's? or put my 245's on the back and get some 225's for the front maybe

pakitagn

I'm running 18x10.5 +22 with a 245/40/18 and only the top of my tire tucks with the stretch. the wheel itself pokes past the fender by a few millimeters. it doesnt rub, but the rubber on a 285 would most likely stick out past the fender. if you punch the numbers into Online Wheel & Tyre Fitment calculator. Offset, Tyre stretch and Rolling Radius calculator, you'll see what i'm talking about.

Driftfc3s

iTrader: (11)

Slight update to the post I made earlier.





Had to drop the front an inch or so more to make it a little more even versus the rear.

negative.one

ok so I've decided to put the 245/30/18's on the rear 10.5 wheels, and I'll buy less wide tires for the front 9" wheels. Is 215/40/18 a good size to get?

Brekyrself

iTrader: (30)

Holy traction. I thought 285's were wide

celm

talk about holy stretch!!

SA3R

For future reference:

18x9.5 +35 all around.
245/40ZR18 all around.
For daily driver use, works 100% fine with no rub, scrape or issues.

I have to run at this stupidly high suspension setting because this is as low as you are legally allowed to go here in Australia :/

negative.one

18x9+25mm, 18x10.5+20mm

soon to be on my black fd, will post pics when it's done. Going with 215/40's on the front and 245/30's on the back