Embarassing: Aftermarket fuel rails/line hookup?
#1
Rotary Freak
Thread Starter
iTrader: (4)
Join Date: Aug 2005
Location: US
Posts: 2,150
Likes: 0
Received 0 Likes
on
0 Posts
Embarassing: Aftermarket fuel rails/line hookup?
So I am bringing my FD to single turbo and I am doing all the work myself and I received my fuel system and I'm trying to figure out where I run my lines. I removed the rats nest/hard fuel lines so if anyone could help me with a diagram or pictures that'd be great.
Also, where/how do I wire these resistors?
Also, where/how do I wire these resistors?
#3
dorito powered
iTrader: (5)
Join Date: Mar 2008
Location: Lincoln, NE
Posts: 2,839
Likes: 0
Received 0 Likes
on
0 Posts
couple ways
BAM
http://kgparts.com/forums/tutorials.php?do=view&tutid=2
http://www.nopistons.com/forums/topi...ments-welcome/
https://www.rx7club.com/3rd-generation-specific-1993-2002-16/fuel-system-upgrade-how-write-up-kgparts-kit-404091/
http://www.3rdgenrx7.com/keithshowto.htm
https://www.rx7club.com/showthread.p...jector+spacers
yeah, I've got them all bookmarked, I recently did the secondary rail and FPR on my car.
BAM
http://kgparts.com/forums/tutorials.php?do=view&tutid=2
http://www.nopistons.com/forums/topi...ments-welcome/
https://www.rx7club.com/3rd-generation-specific-1993-2002-16/fuel-system-upgrade-how-write-up-kgparts-kit-404091/
http://www.3rdgenrx7.com/keithshowto.htm
https://www.rx7club.com/showthread.p...jector+spacers
yeah, I've got them all bookmarked, I recently did the secondary rail and FPR on my car.
#4
Original Gangster/Rotary!
iTrader: (213)
Do not, do not, do not wire in the resistors. Toss them in the trash and buy an FJO injector driver. You'll thank me later. Search in the 3rd gen tech section and there is a thread with an install how-to.
#5
dorito powered
iTrader: (5)
Join Date: Mar 2008
Location: Lincoln, NE
Posts: 2,839
Likes: 0
Received 0 Likes
on
0 Posts
I wired in resistors, wish someone had told me not to sooner. Or for an extra 100-150 dollars, buy injector dynamics high impedance 2200 cc injectors (id2000s)
edit: rich, talking about this thread?
https://www.rx7club.com/showthread.p...ello+peak+hold
-Kyle
edit: rich, talking about this thread?
https://www.rx7club.com/showthread.p...ello+peak+hold
-Kyle
#6
Rotary Freak
Thread Starter
iTrader: (4)
Join Date: Aug 2005
Location: US
Posts: 2,150
Likes: 0
Received 0 Likes
on
0 Posts
Rich what exactly is the FJO injector driver? Did a quick search and found this thread/install DIY. Do you suggest I follow that?
https://www.rx7club.com/showthread.p...njector+driver
https://www.rx7club.com/showthread.p...njector+driver
Trending Topics
#8
Original Gangster/Rotary!
iTrader: (213)
I wired in resistors, wish someone had told me not to sooner. Or for an extra 100-150 dollars, buy injector dynamics high impedance 2200 cc injectors (id2000s)
edit: rich, talking about this thread?
https://www.rx7club.com/showthread.p...ello+peak+hold
-Kyle
edit: rich, talking about this thread?
https://www.rx7club.com/showthread.p...ello+peak+hold
-Kyle
Rich what exactly is the FJO injector driver? Did a quick search and found this thread/install DIY. Do you suggest I follow that?
https://www.rx7club.com/showthread.p...njector+driver
https://www.rx7club.com/showthread.p...njector+driver
#9
Rotary Freak
Thread Starter
iTrader: (4)
Join Date: Aug 2005
Location: US
Posts: 2,150
Likes: 0
Received 0 Likes
on
0 Posts
Howard, I'm glad that for the RX7 it never ends..why? because once you finish with a car what else is there to do but sell it and find another project? lol.
I'll go ahead and shoot you an e-mail.
Where did you guys pickup your FJO setup? Just google searched and bought it or is there a specific version for our FDs
I'll go ahead and shoot you an e-mail.
Where did you guys pickup your FJO setup? Just google searched and bought it or is there a specific version for our FDs
#11
long live the monster BP
Join Date: Nov 2005
Location: New Zealand
Posts: 483
Likes: 0
Received 0 Likes
on
0 Posts
So I am bringing my FD to single turbo and I am doing all the work myself and I received my fuel system and I'm trying to figure out where I run my lines. I removed the rats nest/hard fuel lines so if anyone could help me with a diagram or pictures that'd be great.
Also, where/how do I wire these resistors?
Also, where/how do I wire these resistors?
#12
Rotary Freak
Thread Starter
iTrader: (4)
Join Date: Aug 2005
Location: US
Posts: 2,150
Likes: 0
Received 0 Likes
on
0 Posts
So I will be ordering the FJO instead of wiring in the resisters. However I still have a question. I noticed that I have 3 fuel hardlines. From there, how do I get my fuel lines to hook into those hardlines and third, are there lines running from all 3 outputs of the FPR? I feel like I need to purchase more fuel lines/fittings.
#14
Junior Member
Join Date: May 2009
Location: Northern Ireland
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
no there are 3 harlines coming from the same location but only 2 are the main ones,
There is a feed from your fuel pump
then theres the return from the fuel system your fitting
then the other is for the carcoal canister which i think is for the venting of your fuel tank more so but runs up there then connect to sealed black box with vacum lines on it (located under the oil filler neck)
Im going single and havent had the money yet to opt for the fuel system, but have upgraded my fuel lines and removed the tuning of the third hard pipe as for the hard pip il put a wee kn breather as I think this lets the tank breath..
but if anyone else has any opinion on this third canister line please shed some lit.
As for the injector fjo boxes iv been pricing and for a few extra pound you def are better off with the ID2000 injectors as ya dont need to touch your wiring and plus there bigger again so u can get more fuel if needed through your tuning setups at later stages
There is a feed from your fuel pump
then theres the return from the fuel system your fitting
then the other is for the carcoal canister which i think is for the venting of your fuel tank more so but runs up there then connect to sealed black box with vacum lines on it (located under the oil filler neck)
Im going single and havent had the money yet to opt for the fuel system, but have upgraded my fuel lines and removed the tuning of the third hard pipe as for the hard pip il put a wee kn breather as I think this lets the tank breath..
but if anyone else has any opinion on this third canister line please shed some lit.
As for the injector fjo boxes iv been pricing and for a few extra pound you def are better off with the ID2000 injectors as ya dont need to touch your wiring and plus there bigger again so u can get more fuel if needed through your tuning setups at later stages
#15
BDC Motorsports
#16
BDC Motorsports
#17
Rotary Freak
Thread Starter
iTrader: (4)
Join Date: Aug 2005
Location: US
Posts: 2,150
Likes: 0
Received 0 Likes
on
0 Posts
Ok, so that clarifies the 3 hard lines but which is which?
So basically from the three hardlines, I'll have a single braided line that splits into two braided lines that will connect into my primary and secondary fuel rails, then on the other side of the fuel rails, I'll have two lines coming from them into a single line that goes into the FPR and then a single line that goes from the FPR to the fuel return hardline? Does that seem correct?
Second question is, I have -6an fittings for for lines that I have now...how do I go from the hardlines into my fittings? Is there something I'm missing?
So basically from the three hardlines, I'll have a single braided line that splits into two braided lines that will connect into my primary and secondary fuel rails, then on the other side of the fuel rails, I'll have two lines coming from them into a single line that goes into the FPR and then a single line that goes from the FPR to the fuel return hardline? Does that seem correct?
Second question is, I have -6an fittings for for lines that I have now...how do I go from the hardlines into my fittings? Is there something I'm missing?
#19
Rotary Freak
Thread Starter
iTrader: (4)
Join Date: Aug 2005
Location: US
Posts: 2,150
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for clarifying Drift.
I feel like I don't have a "complete kit" but I may be wrong. Here are some pictures of a straight "bolt on" fuel system kit. Which lines go to what? Also, I feel like the FPR should have 3 AN fittings, not just two.
Here is everything I received in the box
FPR notice how only 2 AN fittings, the third one (on the right) is blocked off
Injectors, resistors and o-rings, no problems here
Primary rail
Secondary rail
All the lines I received. Compared to KG Parts kit found in one of the threads above, there are many lines missing, see the comparison below.
What I have....
What he has...
I feel like I don't have a "complete kit" but I may be wrong. Here are some pictures of a straight "bolt on" fuel system kit. Which lines go to what? Also, I feel like the FPR should have 3 AN fittings, not just two.
Here is everything I received in the box
FPR notice how only 2 AN fittings, the third one (on the right) is blocked off
Injectors, resistors and o-rings, no problems here
Primary rail
Secondary rail
All the lines I received. Compared to KG Parts kit found in one of the threads above, there are many lines missing, see the comparison below.
What I have....
What he has...
#20
dorito powered
iTrader: (5)
Join Date: Mar 2008
Location: Lincoln, NE
Posts: 2,839
Likes: 0
Received 0 Likes
on
0 Posts
feed line>primary rail>secondary rail>FPR>return line
or
feed line>secondary rail>primary rail>FPR>return line
however, if that's what's shown from the place you ordered it from, I would call and ask. The first way is how the factory setup is
or
feed line>secondary rail>primary rail>FPR>return line
however, if that's what's shown from the place you ordered it from, I would call and ask. The first way is how the factory setup is
#22
dorito powered
iTrader: (5)
Join Date: Mar 2008
Location: Lincoln, NE
Posts: 2,839
Likes: 0
Received 0 Likes
on
0 Posts
here ya go, damian illustrates EXACTLY what you're asking about, the top drawing is the factory set-up and is what I'm assuming the lines for your kit are intended to be routed like.
edit: ****, forgot the link
http://kgparts.com/forums/tutorials.php?do=view&tutid=2
edit: ****, forgot the link
http://kgparts.com/forums/tutorials.php?do=view&tutid=2
#23
Rotary Freak
Thread Starter
iTrader: (4)
Join Date: Aug 2005
Location: US
Posts: 2,150
Likes: 0
Received 0 Likes
on
0 Posts
Thanks so much KKM. I tried to make it work but this is what I have right now...I really don't even know if it's possible.
From the feed line, I have a line that runs to my primary rail, then from the other side of the primary rail I have a line going to my secondary rail. From the other side of the secondary rail, it runs to my FPR (does it matter which area it comes into the FPR? side or bottom or does it matter) and then from the FPR I have a line running to the return.
Don't know if these pictures help, but is this ok?
As you see in the picture above, the fuel in goes to the farthest insert of my primary rail, then out the primary and up to the secondary, and then out from the secondary running along the top of the secondary rail and into the side of the FPR. Then from the bottom of the FPR goes to my return line.
From the feed line, I have a line that runs to my primary rail, then from the other side of the primary rail I have a line going to my secondary rail. From the other side of the secondary rail, it runs to my FPR (does it matter which area it comes into the FPR? side or bottom or does it matter) and then from the FPR I have a line running to the return.
Don't know if these pictures help, but is this ok?
As you see in the picture above, the fuel in goes to the farthest insert of my primary rail, then out the primary and up to the secondary, and then out from the secondary running along the top of the secondary rail and into the side of the FPR. Then from the bottom of the FPR goes to my return line.
#24
dorito powered
iTrader: (5)
Join Date: Mar 2008
Location: Lincoln, NE
Posts: 2,839
Likes: 0
Received 0 Likes
on
0 Posts
I was confused by the picture at first, looks like you had a random braided line just going over to the front of the motor and there wasn't anything attached to the back of the secondary rail. But yes, that looks to be correct, just a little weird.
#25
Rotary Freak
Thread Starter
iTrader: (4)
Join Date: Aug 2005
Location: US
Posts: 2,150
Likes: 0
Received 0 Likes
on
0 Posts
Yea I didn't know of any other way for it to work with the lines I already have premade. So it looks like an "S" as far as the flow of my lines go. I will probably double check everything to make sure the connections are good and there won't be any kind of leaking.
One last questions and I believe I'm set. As you see my mines already has -6an fittings. Is there anyway for me to run that to my hardlines? (feed and return) and also, what do I run for the "vent" or do I need a line coming off that.
Also, it doesn't matter where the line comes in or comes out for the FPR correct? I have a line coming into the FPR from my rails on the left side of it and then a line coming out the FPR from the bottom and that goes to my return hardline.
One last questions and I believe I'm set. As you see my mines already has -6an fittings. Is there anyway for me to run that to my hardlines? (feed and return) and also, what do I run for the "vent" or do I need a line coming off that.
Also, it doesn't matter where the line comes in or comes out for the FPR correct? I have a line coming into the FPR from my rails on the left side of it and then a line coming out the FPR from the bottom and that goes to my return hardline.