New Member RX-7 Technical Post your first technical questions here, in an easy flame free environment, before jumping into the main technical sections.

Vacuum leak

Thread Tools
 
Search this Thread
 
Old 03-26-13, 10:36 PM
  #1  
Full Member

Thread Starter
 
TerryD's Avatar
 
Join Date: Oct 2012
Location: Toronto, Ontario
Posts: 145
Likes: 0
Received 4 Likes on 2 Posts
Vacuum leak

Hi all, I have bouncy idle and was thinking it could be a vacuum leak, already check the tps and its within spec. I did a smoke test and i found smoke coming out from somewhere behind the air pump and waterpump area. I'm not sure what would be in that area. any clue/ help would be nice. thx
Old 03-26-13, 11:24 PM
  #2  
Retired Moderator, RIP

iTrader: (142)
 
misterstyx69's Avatar
 
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes on 114 Posts
Did you miss something??
https://www.rx7club.com/new-member-r...swers-1030345/
Old 03-27-13, 07:59 AM
  #3  
Full Member

Thread Starter
 
TerryD's Avatar
 
Join Date: Oct 2012
Location: Toronto, Ontario
Posts: 145
Likes: 0
Received 4 Likes on 2 Posts
Sorry, just remember after i post it, 1987 rx7 na and no mods.
Old 03-27-13, 08:43 PM
  #4  
Full Member
iTrader: (1)
 
redlightrich's Avatar
 
Join Date: Mar 2013
Location: new jersey
Posts: 111
Likes: 0
Received 1 Like on 1 Post
Not certain on your year, but on a 93, that is exactly where intake manifold gaskets sometimes fail.

A can of carb cleaner while running the motor will prove if this is the leak. If you get the leak spot with a stream of cleaner, the idle will smooth for a second.

Good luck with this

Rich
Old 03-27-13, 10:35 PM
  #5  
Full Member

Thread Starter
 
TerryD's Avatar
 
Join Date: Oct 2012
Location: Toronto, Ontario
Posts: 145
Likes: 0
Received 4 Likes on 2 Posts
ON

I dont think so because the smoke flows from like behind the waterpump to in between the air pump and waterpump and up.
Old 03-31-13, 02:25 AM
  #6  
Junior Member

iTrader: (3)
 
True_Talk_Snake's Avatar
 
Join Date: Jul 2012
Location: Washington
Posts: 38
Likes: 0
Received 0 Likes on 0 Posts
My idle Is jumpy from 300-400 rpm in my FD, I checked for leaks and cant find any, Im aiming at its my tune, since I didnt buy this car stock in the first place.
Old 04-01-13, 12:48 AM
  #7  
LOVE2HATEU

 
savicious's Avatar
 
Join Date: Feb 2013
Location: Lodi, CA
Posts: 39
Likes: 0
Received 0 Likes on 0 Posts
That is definitely way below spec. OP maybe made a typo. Did you check solenoids during hose replacement? I'm guessing that the 87 na doesn't have restrictor pills in any lines.
Old 04-01-13, 02:04 AM
  #8  
Retired Moderator, RIP

iTrader: (142)
 
misterstyx69's Avatar
 
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes on 114 Posts
There are a couple vacuum hoses in that area.If you look closely at the area just at the back of the water pump,you can see the Steel lines of the emissions "rack".
Check the hoses on that Mess of lines.
The oil injectors are also run by vacuum too and go to a big "spider connection".4 hoses into one.
You can get the vacuum hose routing off the Factory service manual
Foxed.ca
Or try a search on forum here,,it has been posed before,I actually used it recently.
Old 04-01-13, 10:50 PM
  #9  
Full Member

iTrader: (4)
 
Gumd02000's Avatar
 
Join Date: Mar 2013
Location: Los Angeles
Posts: 73
Received 0 Likes on 0 Posts
I use a can or carb cleaner and start shooting near possible vacuum leak. Idle jump up and soon as it hits the leak
Old 04-02-13, 07:11 PM
  #10  
Full Member

Thread Starter
 
TerryD's Avatar
 
Join Date: Oct 2012
Location: Toronto, Ontario
Posts: 145
Likes: 0
Received 4 Likes on 2 Posts
ON

what will be the easiest way to get to the area? what should i remove to get to it?
also, looking at the vaccum routing, which one may be the cause. cant really do anything with the car till the weekend.

Last edited by TerryD; 04-02-13 at 07:19 PM.
Old 04-02-13, 09:51 PM
  #11  
Junior Member

iTrader: (1)
 
MX_504's Avatar
 
Join Date: Jun 2012
Location: Atlanta
Posts: 31
Likes: 0
Received 0 Likes on 0 Posts
I had the bouncing idle on my FD, spent hours trying to figure it out, and it turned out that the throttle had stuck open, and I'm assuming kept the secondary butterflies open, freaking out the ECU. Just tapped the little actuator and it went back to normal. You might check that, since it should be similar in setup.
Old 04-04-13, 08:40 AM
  #12  
Junior Member
iTrader: (2)
 
nickbroker's Avatar
 
Join Date: Mar 2013
Location: Wisconsin
Posts: 31
Likes: 0
Received 0 Likes on 0 Posts
x2 on bottle carb cleaner....... Mine leaked at UIC found fast
Old 04-13-13, 08:54 PM
  #13  
Full Member

Thread Starter
 
TerryD's Avatar
 
Join Date: Oct 2012
Location: Toronto, Ontario
Posts: 145
Likes: 0
Received 4 Likes on 2 Posts
found my leak, lower intake manifold gasket. T he gasket crack and part of it sticks out. thanks everyone for your help
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM
R.O.D
2nd Generation Specific (1986-1992)
34
01-06-16 12:09 AM
succesfulljoe
1st Generation Specific (1979-1985)
8
09-25-15 04:22 PM
R.O.D
Rtek Forum
1
09-23-15 01:15 AM
gabescanlon
3rd Generation Specific (1993-2002)
4
09-05-15 12:04 AM



Quick Reply: Vacuum leak



All times are GMT -5. The time now is 07:42 PM.