need help with my swap auto to jdm 5speed engine wiring???
#1
Junior Member
Thread Starter
Join Date: Mar 2009
Location: sacramento
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
need help with my swap auto to jdm 5speed engine wiring???
hey im new to these forums and i being alot of research on swapping my engine and the wiring ok so i did all od that now im stuck basicly what im saying is that my 93 fd had auto tranny and i bought a jdm 5 speed engine with engine harness and ecu..droped it in now the wiring for the clutch for the computer i have no idea what to do there can any body help please???
#2
UBER Street Drift
iTrader: (3)
Join Date: May 2009
Location: Tyler, Texas
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
Do you have everything you need for the auto to manual conversion, foot pedals, clutch master and slave cylinders. You'll most likly need to drill the holes to mount the clutch master and clutch pedal, other than that all you should have to do is run your engine wiring through the fire wall near where your ecu is located.
#3
Senior Member
iTrader: (7)
Do you have everything you need for the auto to manual conversion, foot pedals, clutch master and slave cylinders. You'll most likly need to drill the holes to mount the clutch master and clutch pedal, other than that all you should have to do is run your engine wiring through the fire wall near where your ecu is located.
Eric
#5
Senior Member
iTrader: (7)
I'm doing this swap to. You can see some pic at http://erix7rew.monchar.com/ or http://www.clubrxquebec.com/forum/showthread.php?t=5572
I wait for my set of pedal and all the harness for the swap because i dont want to rewire. I want to do a clean swap, just like a real manuel FD
Eric
I wait for my set of pedal and all the harness for the swap because i dont want to rewire. I want to do a clean swap, just like a real manuel FD
Eric
#7
needs more track time
iTrader: (16)
Don't you guys see the FAQ stickied threads at the very top of this forum?
Here is the one for the 3rd gen FAQ:
https://www.rx7club.com/new-member-rx-7-technical-256/frequently-asked-questions-3rd-generation-rx-7-1992-2002-faq-fd-782404/
Scroll down to the A section and you'll see three threads on the topic of Auto to Manual conversion. That should point you in the right direction.
Here is the one for the 3rd gen FAQ:
https://www.rx7club.com/new-member-rx-7-technical-256/frequently-asked-questions-3rd-generation-rx-7-1992-2002-faq-fd-782404/
Scroll down to the A section and you'll see three threads on the topic of Auto to Manual conversion. That should point you in the right direction.
Trending Topics
#8
Junior Member
Thread Starter
Join Date: Mar 2009
Location: sacramento
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Do you have everything you need for the auto to manual conversion, foot pedals, clutch master and slave cylinders. You'll most likly need to drill the holes to mount the clutch master and clutch pedal, other than that all you should have to do is run your engine wiring through the fire wall near where your ecu is located.
#10
merging
Thanks ahead of time!!!!
I apparently I need 3 posts to post in most of the other threads. That's an awful rule to have.
Here's is my third post. So does anyone know if the JDM pedals work in the US cars?
Last edited by gracer7-rx7; 06-08-10 at 10:34 AM. Reason: merging
Thread
Thread Starter
Forum
Replies
Last Post
befarrer
Microtech
3
08-22-15 05:52 PM