first time swapping engine need help.
#1
Junior Member
Thread Starter
Join Date: Sep 2014
Location: Edmonton
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
first time swapping engine need help.
hello everyone, i am doing my first swap ever on a 1990 NA fc. And i am stuck at the engine harness due to not sure how it should be tuck. it is tuck under the rat nest going from oil dipstick toward front then to the other side? or some other way? plz help me and when bolting the transmission on, one of the censor on the cylinder clutch broke off due to old age. can anyone also tell me wat that censor is for? and do i need it to start the car. thanks you soooo much guys.
the harness should be tuck under the rat nest or other way?
wat cencor is this? the wire broke off and it mount on the clutch cylinder
the harness should be tuck under the rat nest or other way?
wat cencor is this? the wire broke off and it mount on the clutch cylinder
#3
Moderator
iTrader: (3)
1. i don't know (however, if you feel up to searching, you can look at thread called She Followed Me Home, Honestly by the user Clokker. if i recall he has some good disassembly/reassembly photos on his Rx-7. the thread is HUGE though, so finding them may take some time.)
2. i believe that is the condenser that dampens the oil pressure gauge.
2. i believe that is the condenser that dampens the oil pressure gauge.
#4
Junior Member
Thread Starter
Join Date: Sep 2014
Location: Edmonton
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
1. i don't know (however, if you feel up to searching, you can look at thread called She Followed Me Home, Honestly by the user Clokker. if i recall he has some good disassembly/reassembly photos on his Rx-7. the thread is HUGE though, so finding them may take some time.)
2. i believe that is the condenser that dampens the oil pressure gauge.
2. i believe that is the condenser that dampens the oil pressure gauge.
For number one and number two where does these two connect into? Thanks<br/>
Also where is the cap one suppose to connecting to?
Last edited by bomh; 10-25-15 at 05:44 PM.
#6
Junior Member
Thread Starter
Join Date: Sep 2014
Location: Edmonton
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Thanks Satch. Anyone know where the 2 hose go to?
#7
Moderator
iTrader: (1)
Look at the White plastic object on the rear of the throttle body which you have a pic of. One hose is capped while the other one is not. Find where the uncapped one leads to. If it makes its way to the front of the throttle body and plugs into the double throttle diaphragm then the capped port is to run to the manifold just bellow the capped port which might well appear in the pic. The FSM has a diagram of this.
Trending Topics
#8
Junior Member
Thread Starter
Join Date: Sep 2014
Location: Edmonton
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Plz anyone? Everything is in the car except I don't know where this is connecting into. Plz help me out<br/>
I don't know where this hose going into ether. Is it connect together with the other pic?
#9
Moderator
iTrader: (1)
And you'll need a check valve too. (this info was already stated above).
https://www.rx7club.com/2nd-generati...aphram-735858/
Look at post #17 and focus on the green highlight.
https://www.rx7club.com/2nd-generati...ee-pic-783951/
The 2nd pic hose runs to a port just behind the oil pedestal and to the right of it (port faces the fire wall).
https://www.rx7club.com/2nd-generati...aphram-735858/
Look at post #17 and focus on the green highlight.
https://www.rx7club.com/2nd-generati...ee-pic-783951/
The 2nd pic hose runs to a port just behind the oil pedestal and to the right of it (port faces the fire wall).
Last edited by satch; 10-30-15 at 03:55 PM.
Thread
Thread Starter
Forum
Replies
Last Post