I put my NES in my car as the active (hip) gaming system. i want to Glen Burnie McDs and played duck hunt out the hatch! Bah-ling Bah-ling!

EDIT: I just had the idea with that bling statement, I'm gonna paint the gun shinny gold.

 

paint it platinum yo... bling bling

 

Wow, theres like, seven unsecured wireless networks in this neighborhood.

(I'm in Blacksburg, VA)

Why would I ever actually PAY for internet access?

 

then don't :P
and connect all the netoworks so you have a good solid connection base

 

meh, I enjoy my university connection except the UMBC firewall is really gay...


EDIT: woah, I broke 600, yay

 

i did that at home, since dad's too much of a retard to wire everything up...when our router dies(like it does just about every day) i leech off the neighbors. when they're stupid, i "borrow"

 

I loooooove that Free internet? Why thank you very much!

 

Grr... frickin e-shaft bolt won't come off. Even with my impact tools and 4 foot cheater bar.

 

try some WD-40

 

You have to heat it with a torch, then it pops right off. If you can get it to glow... that's the ideal temp.

 

I ended up heating it. I was a little worried at first because of the 140-degree thermostat thats directly behind the bolt but I don't think I'm going to be putting it back in anyway so off came the e-shaft bolt. Now the flywheel nut, thats a whole new epic. Bent two angle irons so far just picked up a third which is slightly thicker than the other two so we'll see soon enough. Also went and bought a bigger compressor and tank. YAY!

 

I hate daylight savings time... I didn't wake up till 4 today class tomorrow is going to suck...

 

dang it, springbreak is over...back to school for me =[

 

I hear yeah, mike its like 4:30 now, and I just woke up.....must go find chinese food...argh.

 

I'm sitting here doing homework all day
but that 13B N/A power is calling to me.. it's singing in my head.

I'm sure many of you might be past that feeling, but this is still new to me.. my first car.. and I love it

 

When do the Ihop meets on 355 in rockville start again? id like to come down a few times this summer.

 

my guess is probably around mid may sometime when everyone gets out of school...

-Myk

 

Well... FD motor is completely apart. Housings and rotors "look" good so I think I can get away with just a rebuild kit. I'm still a little leary about ordering it just yet. I'd rather wait until I can check for warpage and what not so I don't end up with a rebuild kit and still have to buy a new motor.

I wanted to have the motor apart last night so I could clean everything today but it looks like I"m going to have to wait until friday to do the cleaning unless I take a day off work this week. Thats going to set me back about a week on getting the FD back on the road since I doubt I'd order the kit until I've cleaned and then checked everything. I'll probably take pics, tired and hungry right now. I love my new compressor

 

welll... when i get the motor from Eightman... i'll do the same thing.. what exactly does the rebuild kit comes with?

 

This is the content list for RSR's rebuild kit. I'm still going with Mazda OEM seals though.

4 TEFLON ENCAPSULATED SILICON Inner Water Coolant Seals
4 TEFLON ENCAPSULATED SILICON Outer Water Coolant Seals
4 VITON Inner Rotor Oil Seal O-rings
4 VITON Outer Rotor Oil Seal O-rings
4 VITON Dowel Pin O-rings
1 VITON Rear Stationary Gear O-ring
1 Front Cover O-ring
1 Nylon Washer for Front Cover Pulley
1 Oil Metering Pump O-ring
2 VITON Oil Filter Base O-Rings
18 Tension Bolt Washers
1 VITON E-shaft pulley bolt O-ring
6 Injector Diffuser O-rings
1 Crank angle sensor O-ring
1 Oilpan gasket (shipped separately)
1 Front cover gasket-metal (shipped separately)
1 Front Main Seal
1 Rear Main Seal
12 Corner Seal Springs
12 Side Seal Springs
12 Corner Seals
12 Side Seals
6 Apex Seals w/ dual springs
1 Waterpump to Block gasket
1 Oil Tube Gasket
1 Hylomar
1 Brushable Sealant
1 Grey 999
1 Thermal Plug
1 Oil Pump Chain
4 Rotor Oil Seal Sets
4 Rotor Oil Seal Springs (Inner)
4 Rotor Oil Seal Springs (outer)
Instruction Set

 

finally got the FC inspected over the weekend, in the rain :down:, on 1.5 hours sleep :down:, with no breakfast :down:

and for 360 f'in bucks


jesus christ

well at least that afventure of getting the car back on the road and tagged is almost over, its crazy how hard it is to get a car like that through the system

cant wait for the IHOP meets to start pissin off the rotorheads... sweetness

 

Welp I sold my Black GTU. So, This week I'm getting, wedding rings, a new tank/barrel for the PB gun, RB turbo back exhaust, and the rest is going into savings for honeymoon to ireland.

 

i have a tank for a paintball gun if you want it...

and what is the thread on the barrel ... i have a custom one that i made a long time back ... its heavy but its super accurate


it fit on a brass eagle raptor

 

I have a system-x autococker. I need a BIG tank however w/anti-siphon, etc.

 

20 oz big enouigh and it has an anti-siphon valve on it ...