How much horse power is possible out all motor?
#28
Eats, Sleeps, Dreams Rotary
iTrader: (1)
And that's why the 4 bangers are allowed to have a much lighter chassis than a rotary in the drag racing classes because they bitched and moaned that the rotary has an unfair advantage in displacement and power and etc., and that's the only reason and way they can compete against the rotary. If it was even steven than the rotary would be first place all day long.
#31
#33
#35
Eats, Sleeps, Dreams Rotary
iTrader: (13)
Join Date: Aug 2002
Location: Pittsburg, KS.
Posts: 4,152
Likes: 0
Received 0 Likes
on
0 Posts
take a look here
http://www.dragtimes.com/horsepower-...power+Estimate
http://www.dragtimes.com/horsepower-...power+Estimate
#36
take a look here
http://www.dragtimes.com/horsepower-...power+Estimate
http://www.dragtimes.com/horsepower-...power+Estimate
#37
Eats, Sleeps, Dreams Rotary
iTrader: (1)
Hey Cris, what was Padilla's final weight? With the roll cage and complete interior that has to be pretty close no? Bone stock first gen is 2400lbs+ roll cage, driver, minus stock seats and a couple of misc= around 2300+ in my calculation. Am I missing something?
Last edited by ultimatejay; 06-22-08 at 11:13 PM.
#41
#42
InsaneRotaries.com
Last year one of those FWD **** had an interview on camera and he talked about 400hp dyno slips... They're obviously making the power and after all these years, they've finally gotten the science of putting the power down and making a clean run... These guys have no excuses or handicaps and the way the **** and moan about the RWD cars are very unfair.. I say we take it back to run what you brung
#43
Eats, Sleeps, Dreams Rotary
iTrader: (1)
Last year one of those FWD **** had an interview on camera and he talked about 400hp dyno slips... They're obviously making the power and after all these years, they've finally gotten the science of putting the power down and making a clean run... These guys have no excuses or handicaps and the way the **** and moan about the RWD cars are very unfair.. I say we take it back to run what you brung
#44
i love my honda
and my 7
but **** wheel hop on fwd, **** sucks ****... but im sure if i could launch better it wouldnt be a problem. and if ya bought a fwd, you shouldve known that it does have some flaws as far as racing is concerned... so they should shut up and buy a rx7
and my 7
but **** wheel hop on fwd, **** sucks ****... but im sure if i could launch better it wouldnt be a problem. and if ya bought a fwd, you shouldve known that it does have some flaws as far as racing is concerned... so they should shut up and buy a rx7
#45
Full Member
20B all motor
Ok, I've been reading through some of these comments regarding the 20B HP gains. A 20B with a mild streetport and a good tune will make 325-350 to the wheels, if not more. There are a lot of variables that go into make really good HP from a 20B but it's been repeated done by many. Just my 2 cents !
#47
you do know that you can build a bridge port 12a with twin side draft 55 DIA and run 2000 cc injectors and produce 248hp pre tuned. I know I've seen it so why would it be hard to reach the 400 mark like he is wanting. its still a lot more money and hard to achieve but it can be done and you will be rebuilding it all the dang time LoL
Thread
Thread Starter
Forum
Replies
Last Post
immanuel__7
2nd Generation Specific (1986-1992)
89
09-05-15 10:23 AM
16, 2000, 200hp, 2nd, break, california, generation, horse, horsepower, integra, mazda, peripheral, port, power, rx7, streetabe