Microtech Msd Coils Not Shooting?? Please Help
#1
187 RX7 Gone To Heaven
Thread Starter
Join Date: Apr 2008
Location: Lakeland, Florida
Posts: 232
Likes: 0
Received 0 Likes
on
0 Posts
Msd Coils Not Shooting?? Please Help
Hi i have a microtech lt10s with x4 box..... i have the coils wired the correct way because about a week ago when the car was still not completed we started the engine. but for reasons unkown to me the coils are getting power to the positive side of the coils and the negative side. i know its not the wiring because i have power only running to the positives on the coils. and the negatives are connected to the X4 box..
please someone help me i really cant figure this out!
thank you,
Vic
please someone help me i really cant figure this out!
thank you,
Vic
#3
187 RX7 Gone To Heaven
Thread Starter
Join Date: Apr 2008
Location: Lakeland, Florida
Posts: 232
Likes: 0
Received 0 Likes
on
0 Posts
ok.. the Microtech itself shows the orange light flashing (the ignition pulse light).. so i would have to send it in to microtech then... and how can that happen if i havent done anything to it.. it jus sat in the car i haven driven the car or nothing
#5
187 RX7 Gone To Heaven
Thread Starter
Join Date: Apr 2008
Location: Lakeland, Florida
Posts: 232
Likes: 0
Received 0 Likes
on
0 Posts
no sir the test light wont flash to negative?? i just has steady power to both sides... do you think theres something wrong with the microtech??
#6
Rotary Freak
iTrader: (8)
Have you grounded the earth wire that goes to the x4 box, to the block.
Why did you use MSD coils and not the bosch coils?
Microtech dont recommend any of the MSD gear. Recommend bosch.
If your earth wire from the x4 box is grounded and still no spark.
The x4 box/microtech need to be sent back.
Why did you use MSD coils and not the bosch coils?
Microtech dont recommend any of the MSD gear. Recommend bosch.
If your earth wire from the x4 box is grounded and still no spark.
The x4 box/microtech need to be sent back.
#7
187 RX7 Gone To Heaven
Thread Starter
Join Date: Apr 2008
Location: Lakeland, Florida
Posts: 232
Likes: 0
Received 0 Likes
on
0 Posts
i have the x4 grounded but not to the block? its on the firwall...
how can i go about sending the x4 box/microtech back???
the MSD's were recommended from a shop where im from, but when i first finished the setup the MSD's worked very well.
how can i go about sending the x4 box/microtech back???
the MSD's were recommended from a shop where im from, but when i first finished the setup the MSD's worked very well.
Trending Topics
#8
Rotary Freak
iTrader: (8)
Next time dont use them. I have never had anything but trouble from MSD.
AND your ground should be on your BLOCK.
This is what has killed your X4.
Youll have to send the microtech back to a dealer here in sydney. And they will have it dropped off at Microtech Putney to be repaired.
or you can send it to John at www.microtechefi.com
AND your ground should be on your BLOCK.
This is what has killed your X4.
Youll have to send the microtech back to a dealer here in sydney. And they will have it dropped off at Microtech Putney to be repaired.
or you can send it to John at www.microtechefi.com
Thread
Thread Starter
Forum
Replies
Last Post