Microtech Matrix Mode
#1
Scream baby Scream!!!
Thread Starter
Join Date: Sep 2002
Location: Warrenton, VA.
Posts: 435
Likes: 0
Received 0 Likes
on
0 Posts
Matrix Mode
Can anyone explain or have a demo of how to use the matrix side of the ecu. I had my laptop hooked up to it this weekend and switched it to matrix and it came up with the screen and highlighted each individual block as I reved the engine, but, I couldn't see how to input any figures into the blanks. I'm still running really rich at idle and the car tends to load up and start smoking and if it idles too long it starts to really get bad. I have all low imp injectors and I know they don't spray as nice as the high, but they are only 750 pri and 1000 sec. I believe if I remember right the secondaries don't come on until 3000. So, rich idle (11.0), trying to fix with matrix tuning at idle to correct loading up.
#2
Junior Member
Join Date: May 2006
Location: Salzburg / Austria
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
Have you read the manual "programming guide" --> "fuel control functions"?
Go to screen 1 and screen 8 to set up the basics. Later on you can go to screen 34 for copying the setup to the rest of the screens 2-16.
Roland
Go to screen 1 and screen 8 to set up the basics. Later on you can go to screen 34 for copying the setup to the rest of the screens 2-16.
Roland
#3
Rotary Freak
iTrader: (8)
11.0 idle isnt that rich.
With the microtech your not going to get it much leaner without other headaches coming up.
i usually set them to 11.4-11.7 and no leaner.
ALSO. Matrix mode is very simple. Click on the cell you want to adjust and put in your number in it. Simple.
With the microtech your not going to get it much leaner without other headaches coming up.
i usually set them to 11.4-11.7 and no leaner.
ALSO. Matrix mode is very simple. Click on the cell you want to adjust and put in your number in it. Simple.
#4
Scream baby Scream!!!
Thread Starter
Join Date: Sep 2002
Location: Warrenton, VA.
Posts: 435
Likes: 0
Received 0 Likes
on
0 Posts
I tried that, but there was no entry on the screen. I'm only trying to lean out enough to stop from loading up. Its getting better as I go, now I thinks its just fine tuning it needs. Thats what I was trying to do with the matrix mode. I didn't think it was that hard, but whatever I'm doing isn't making any changes and theres no indication on the chart I made an entry. I'll try it again and see if maybe I was on crack that day and missed something.
#6
Mm....i know the matrix mode is simple but for the death of me i can't seem to get it to work. A short video would be great :P cause i am the see it to know it kinda guy :P I have read the manual a few times to no avail.
ps; i am running a MT8 So the hand controller is the only thing i can use
ps; i am running a MT8 So the hand controller is the only thing i can use
Trending Topics
#8
My bad i should have been more clear. I used a friend's laptop to try using the matrix or the laptop tuning but i could not get it to work. Cause the previous owner said it was a MT8 which he had upgraded. I guess he was blowing smoke
So most of the tuning has been done though the hand controller by a local tuner. It is not a bad tune but it is still to rich. How do i know if it has been upgraded ?
So most of the tuning has been done though the hand controller by a local tuner. It is not a bad tune but it is still to rich. How do i know if it has been upgraded ?
Thread
Thread Starter
Forum
Replies
Last Post
24seven_dada
3rd Generation Specific (1993-2002)
20
11-10-18 12:03 PM
befarrer
Adaptronic Engine Mgmt - AUS
3
09-22-15 09:33 AM