Megasquirt pull up resistors
#1
Banned. I got OWNED!!!
Thread Starter
Join Date: Jun 2004
Location: ft collins, co
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
pull up resistors
ok i just installed the pull up resistors on all three led's. when i turn the megasquirt on with the stim.. those three led's stay lit continuously.. is this correct?
#4
Banned. I got OWNED!!!
Thread Starter
Join Date: Jun 2004
Location: ft collins, co
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
ok well heres the deal.. i had 3 wires running from the 3 leds to the db37 pins 10, 11,12. i cut the wires from the led's to the pins and now it flash as it should. so i measured voltage from ground to pin 10,11,12 - nothing . so i measured between 5v and those pins and got 5 volts.. telling me that those pins are somehow connected to ground. is this correct.. and if so what pins should i connect my spark outputs to?
another question. does the megastim connect those 3 pins to ground?
another question. does the megastim connect those 3 pins to ground?
#5
Gen 2 Raced Hard NA 13B
Join Date: Apr 2006
Location: Canada
Posts: 272
Likes: 0
Received 0 Likes
on
0 Posts
Electrical Drawings
Below is a link that will help you out. It will have drawings showing the wiring of the board and pins.
Good Day
http://www.megamanual.com/ms2/pcb.htm
Good Day
http://www.megamanual.com/ms2/pcb.htm
#6
Banned. I got OWNED!!!
Thread Starter
Join Date: Jun 2004
Location: ft collins, co
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
^^ thats for a MSII im running a MSI v3. so heres my findings MS v3 has 4 spare output pins spr1 spr2 spr3 spr4; pins 3,4,5,6 respectively.
i am set up to run bac, vdi, aux ports, spark A,B, &C. so my 4 spares will be spr1-vdi, spr2-aux, spr3- launch control in, spr4- spare
my bac will be controlled by fidle - pin 30
so i was planning on using pins 10,11,12 for spark output but that seems not to work..
i looked up quasar's pictures of his board and it appears that he is taking the spark outputs to the iac outputs.
https://www.rx7club.com/megasquirt-forum-153/dual-vr-sensors-ms1-v3-build-pix-633573/
i think im just goin to do this. it should take care oc my problem.
i am set up to run bac, vdi, aux ports, spark A,B, &C. so my 4 spares will be spr1-vdi, spr2-aux, spr3- launch control in, spr4- spare
my bac will be controlled by fidle - pin 30
so i was planning on using pins 10,11,12 for spark output but that seems not to work..
i looked up quasar's pictures of his board and it appears that he is taking the spark outputs to the iac outputs.
https://www.rx7club.com/megasquirt-forum-153/dual-vr-sensors-ms1-v3-build-pix-633573/
i think im just goin to do this. it should take care oc my problem.
#7
Rotary Enthusiast
Originally Posted by monkhommey
^^ thats for a MSII im running a MSI v3. so heres my findings MS v3 has 4 spare output pins spr1 spr2 spr3 spr4; pins 3,4,5,6 respectively.
Schematics for the stim are online there as well, or you could also just check with a meter to see which stim pins are grounded.
Thread
Thread Starter
Forum
Replies
Last Post
HalifaxFD
Canadian Forum
126
05-09-16 07:06 PM