AEM coil upgrade package preview/interest
#78
We may do an alternate mount but I can't make any promises just yet. They'll need a new spec'ed set of plug wires and new harness as well so it would be an entirely new setup. Obviously it's dependent on interest... we could get an alternative mount interest thread going if you guys want .
-Heath
#81
It depends how we do it. If the design is similar yes, if it's more complex obviously the price will be affected. Getting the current kit through production is our main goal at the moment. If you guys can show enough volume/interest to warrant a redesign we'll consider it.
-Heath
-Heath
#86
DRIVE THE ROTARY SPORTS
iTrader: (5)
Join Date: May 2003
Location: CA (Bay Area)
Posts: 4,150
Likes: 0
Received 0 Likes
on
0 Posts
For those of you that want to do your own wiring harness or plug wires we might be able to get close, but with all of the parts totaled (coils, bracket, plug and play harness, spark plug wires) up we're not going to be able to hit the 500 mark. The design of a RHD/non brake cruise location will be more as well since it would have to be a much more complicated CNC bracket design.
We can't provide ultra-small-run parts at cheap prices and stay in business. There's little volume/profit in the FD market as it is, and most of our parts are sold in the 10's Nearly all of our "profit" on parts goes back into R/D for new parts development.
We can't provide ultra-small-run parts at cheap prices and stay in business. There's little volume/profit in the FD market as it is, and most of our parts are sold in the 10's Nearly all of our "profit" on parts goes back into R/D for new parts development.
#87
Senior Member
iTrader: (4)
For those of you that want to do your own wiring harness or plug wires we might be able to get close, but with all of the parts totaled (coils, bracket, plug and play harness, spark plug wires) up we're not going to be able to hit the 500 mark. The design of a RHD/non brake cruise location will be more as well since it would have to be a much more complicated CNC bracket design.
We can't provide ultra-small-run parts at cheap prices and stay in business. There's little volume/profit in the FD market as it is, and most of our parts are sold in the 10's Nearly all of our "profit" on parts goes back into R/D for new parts development.
We can't provide ultra-small-run parts at cheap prices and stay in business. There's little volume/profit in the FD market as it is, and most of our parts are sold in the 10's Nearly all of our "profit" on parts goes back into R/D for new parts development.
Thank you for providing innovative products to the community and your passion to an "old" chassis
#92
Eats, Sleeps, Dreams Rotary
iTrader: (52)
Can I get a top picture, looking down directly at the coils and bracket? I have some new brake lines and a bias that will be a close fit. Probably in on this even if I have to move it...again.
And yes, you guys rock! Great products as always. Its like you are reading my wallet's mind!
And yes, you guys rock! Great products as always. Its like you are reading my wallet's mind!
#99
Ok ok if you insist.
We'll have product shots up and a 'pre-order' sale going on the website shortly. We were hoping to have them finished ready to ship instead of asking people to wait, but the finishing shop for powdercoating and anodizing has been taking longer than we expected. We should have the brackets and wires "in stock" by the end of the week. There will be a short lead time on coils. Our harness won't be ready to go for a few weeks however. We'll leave those off the site for now. Anyone requiring a harness that was part of the original prep-sale would get the same pricing and free shipping on the harnesses.
Hopefully we've made enough of these kits to satisfy demand... I'm a little nervous about quantities available since we didn't think there would be nearly as much demand as there seems to be now
-Heath
We'll have product shots up and a 'pre-order' sale going on the website shortly. We were hoping to have them finished ready to ship instead of asking people to wait, but the finishing shop for powdercoating and anodizing has been taking longer than we expected. We should have the brackets and wires "in stock" by the end of the week. There will be a short lead time on coils. Our harness won't be ready to go for a few weeks however. We'll leave those off the site for now. Anyone requiring a harness that was part of the original prep-sale would get the same pricing and free shipping on the harnesses.
Hopefully we've made enough of these kits to satisfy demand... I'm a little nervous about quantities available since we didn't think there would be nearly as much demand as there seems to be now
-Heath