Hes just unorganized and lacks the responsibility to run a buisness, simple as that.
I held my tongue for the sake of discretion while i went through all of the above, but reading through this thread seeing how many other people are being put out and a good business going down the drain, im telling it like it is.

 

I did eventually get my parts, just disappointed with the lack of communication and huge delay.

 

Yip.

 

Well he stopped replying again.... ****

 

Anybody recieved their parts? Communication has stopped again.

 

^ such a shame!

I wanted to order some parts forum FB too

 

i ordered some bearings for my camber plates, got them in 4 days. I think there is just problems with his machined parts. hopefully he can chime in here and talk to us though.

 

Well I've finally been able to get my machinist switched over to another person and things should finally be back on track now.

I finally have all the parts ready for the oil fillers. All the oil filler orders should be shipped out tomorrow. (Have about 14 pieces)

The front coil over tops are being machined today and will be done later on today. (22 pieces of those will be done)

Front Big brake kit hub adapters are next on the list, then followed by the rear coil over parts. So if all goes well everyone will have all their parts shipped out by the end of next week!

 

So can I order a filler neck now and not wait months to recieve it?

 

If you order it right now, it'll be shipped out tomorrow with the other 4

 

Ok. Just paid for a filler with the -10AN fitting.

 

Wanted to chime in. I needed some parts that only Sam had (axle plates a bbk adapters) but wasn't sure if I should place an order b/c of this thread. But I had no choice and decided to talk to Sam first. I did the entire order through email and paid by paypal. He even gave me a discount on the rear bbk because I didn't need the handbrake hardware. Placed the order on Jan 18, got shipped last week, and got the parts today. The communication was there and he did let me know ahead of time the the alternator pulley that I included w/ the order will take some time because he was waiting on the machine shop. Overall good experience. Thanks Sam!

 

Good to know. Let us know when they ship Sam.

 

Got shipping confirmation for my oil neck!

 

Got mine, too.

 

Interested in the steering kit upgrade. My car has a alternator relocate and the Tii engine swap, how will I know if the steering linkages will clear the alternator.

this picture kinda shows where the alternator is located. Anyone at Re Speed want to chime in and help me figure this out?
Also is this steering kit stage 2 currently available?

 

Ive done a couple small orders with sam through email lately. ive had nothing but fast responses and fast shipping. i think he's getting things caught up.

 

Assuming your alternator isn't any lower than the a/c compressor would normally be then you will be fine. I had the kit on my car with a/c and it cleared the bracket fine.

 

so did the orders ship out yesterday or what?!?!

still no answer or reply on any re-speed emails or phones, im so sick of it...

5 months? really?

beginning to wonder if his latest machinist excuse is just another scheme to get us to stop bothering him for a few more months.

RE-SPEED HAS HORRIBLE BUSINESS CONDUCT.

 

I got shipping comfirmation and a tracking number for mine on the 19th i believe. It has entered the states and is en route.

I agree the customer service sucks. I think he needs a secretary...

 

Holy ****!

 

TBH i read all this and was 50/50 if i should buy a Filler Neck from them, But in all fairness they have responded to all my E-mails within a Day so i went ahead and bought one last week end.

So we'll see how that goes, but tbh with you there Customer service is much Better than i expected it to be but i'll leave final Judgment until the Filler is in my Hand

 

The response comes and goes. Sometimes he will answer and sometimes u will get nothing from him for weeks...

Good luck

 

I received the oil filler neck last night as well.

 

Nice parts! Wish i could get mine too