Just finished single wire harness ..wires in good shape, so no need for rywire Just yet. .
Anyway my dumb *** broke the lock on the crank angle sensor plug/clip
-Can you get just a plug from somewhere, or does anyone have one for some reason they can part with
-Also can't figure out how to depin crank sensor clip, it's different then the other clips
-My new ev14s secondary injectors clips look to be the same as factory, should I just leave them be or solder in New clips
Thanks
Brad

 

Sumitumo 2 Pos Female

 

Blue unused connector on the harness is the same as the cas. 2000cc ev14s plug into the factory secondary connectors. If they are in good shape you can leave them.

 

This is why I love this site. .
I'll check the removed blue plug if it's ok , other wise I'll order one. .
Just need to play with plug and get it depined

 

Looks like I'll order one. . Broke pin lock. Then tab holding pin in broke, Purdy crispy
Thinking I might depin injector clips use new ones now

 

One more question before I wrap up the harness
Took a second look at secondary injector clips the red wire on new clip lines up with black and yellow wire, now I'm assuming the injectors use the black and yellow wire as power...?
And the ecu as the ground?
If that's the case I'll have to switch the primaries around, I soldered black on new clip to black/yellow wire, assuming it was a ground since they were all tied together

 

Im at work but you should have it right...the ecu grounds each injector via the the colored wires. If you have a multimeter just turn the ignition on and test the wire in question for power or lack there of.

If someone doesn't chime in before I get off work I'll look up the exact wires for you.

 

Alright thanks.
Gonna depin secondary injectors use new clips, I'll take shrink tubing off primaries and solder wires around the other way
Red to blk/yel

 

I ordered a couple new connectors too.

Do any of you guys know where I can get the plastic push clips that attach to the connectors so you can hold them in place?

 

 

Was looking over that in my book, just wanted to confirm B/Y was power, I switched them around,
Thanks
Tryed to use new clips with factory wire and metal tab, but locking tab is different, I'll be soldering New wires and clips on tomorrow
Thanks again

 

what did you switch around? when people say that it worries me.....

 

The wires on primary injectors
There now connected red wire on new clip to blk/yel on harness

 

Ordered crank angle sensor clips from tripointengineering, one month later and I don't have the damn things
They don't answer emails or there phone
Anyone have another place I can order them from
My spare blue clip is broke also so that's out

 

^ me too buddy, me too. That reminds me, I actually need to call and cancel my order because I ordered from this guy:

Sealed

And they've already shipped.

 

That's what I needed, thanks
Got a hold of him said he was going to look for them if not he order them ,think I'm gonna cancel also

 

I just called and cancelled.

Apparently, like 10 days before I ordered, tri point went under new management and left a lot of loose ends.

Lets hope when they get things together, they'll be a better business.

 

That site 20 dollar min purchase or its 5000dollars to ship lol
Got to be another place to order just need 2 clips

 

It says that on the opening page, but those connectors are ridiculously cheap by comparison to tri point.

I picked up 3 times as many as I ordered from tri point for less than half the cost.

 

Just order more, it's totally worth it. You'll probably be able to sell them here for a profit.

 

If anyone needs connectors shoot us a heads up... We typically stock many of the underwood connectors for just this reason.
Info@sakebombgarage.com

 

Update ...received my package today around 8 days after I ordered. .east beaver shipped very next day after I ordered