Wanting to install stock wing, how do I align it?
05-01-03, 01:15 PM
#3
Full Member
Join Date: Jan 2003
Location: San Rafael, CA
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
I'm interested too. I was just going to tape some brown packaging paper on the rear hatch where the mounts are, line up the wing, trace it and then use the rubber gaskets to locate the holes. It shouldn't be that hard. Tom
05-01-03, 01:45 PM
#4
2 babies - no back seats
Join Date: Nov 2001
Location: N. Wilm., Delaware?
Posts: 981
Likes: 0
Received 0 Likes
on
0 Posts
Try here: http://www.scuderiaciriani.com/rx7/spoiler_install.html
Print the files at 100%, cut out, align, and tape together to make a templete...
Print the files at 100%, cut out, align, and tape together to make a templete...
05-01-03, 02:39 PM
#6
Lawn Ornament
Thread Starter
Originally posted by rotary-tt
Try here: http://www.scuderiaciriani.com/rx7/spoiler_install.html
Print the files at 100%, cut out, align, and tape together to make a templete...
Try here: http://www.scuderiaciriani.com/rx7/spoiler_install.html
Print the files at 100%, cut out, align, and tape together to make a templete...
Trending Topics
05-01-03, 05:42 PM
#8
Lawn Ornament
Thread Starter
Originally posted by rotary-tt
Spend some time on this site if you have not already. Most is pretty old but still relevant...
Spend some time on this site if you have not already. Most is pretty old but still relevant...
05-01-03, 06:38 PM
#9
Blow up or win
Eyeballing is really pretty damn good if you take your time. As good as a template.
Use a water based fine tip magic marker once you have it set just right.......
Use a water based fine tip magic marker once you have it set just right.......
05-01-03, 08:45 PM
#10
2 babies - no back seats
Join Date: Nov 2001
Location: N. Wilm., Delaware?
Posts: 981
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by ejmack1
lol, im not new here man, I have used that site quite frequently in my 2 years with this car. I did not ever see that on there though.
lol, im not new here man, I have used that site quite frequently in my 2 years with this car. I did not ever see that on there though.
04-10-04, 10:37 AM
#11
Originally posted by rotary-tt
Try here: http://www.scuderiaciriani.com/rx7/spoiler_install.html
Print the files at 100%, cut out, align, and tape together to make a templete...
Try here: http://www.scuderiaciriani.com/rx7/spoiler_install.html
Print the files at 100%, cut out, align, and tape together to make a templete...
04-10-04, 11:51 AM
#13
Rotary Freak
Join Date: May 2002
Location: Houston
Posts: 1,742
Likes: 0
Received 0 Likes
on
0 Posts
04-12-04, 06:36 PM
#15
Rotary Freak
Join Date: May 2002
Location: Houston
Posts: 1,742
Likes: 0
Received 0 Likes
on
0 Posts
In that case, that template should work fine. Print it out and check by taping it on your hatch, and putting the 99 tail on top. Once you use that template to get a few of the common holes (between the R and the 99 tails), then you can use the other method to get the uncommon holes for the 99 tail.
Last edited by PVerdieck; 04-12-04 at 06:39 PM.
Thread
Thread Starter
Forum
Replies
Last Post
