3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Tranny or clutch? 5th gear issue... *searched*.

Thread Tools
 
Search this Thread
 
Old 07-30-11, 08:06 PM
  #1  
Forever blown!

Thread Starter
iTrader: (14)
 
MuRCieLaGo's Avatar
 
Join Date: Jul 2007
Location: Trois-Rivieres (QC)
Posts: 1,370
Received 13 Likes on 10 Posts
Tranny or clutch? 5th gear issue... *searched*.

When I enter the 5th gear and I push the gas pedal, it comes back to neutral. *No grind*. If I keep pushing the 5th gear with my hand while I push the gas pedal, it's all fine.

Sounds like a tranny problem or clutch?

I'd say tranny but I just wanna be sure...

J-Spec or rebuild? I already have an old J-Spec that make some noises but is running #1.
Old 07-30-11, 08:57 PM
  #2  
Full Member
 
RotoryDreamer's Avatar
 
Join Date: Jul 2011
Location: Wisconsin
Posts: 51
Likes: 0
Received 0 Likes on 0 Posts
Defiantly tranny something is keeping it from fully engaging 5th whether its a syncro or shift fork or shift rod something is hanging it up.

As far as rebuild or the jspec sounds like they both will need a rebuild so take your pick. The jspec may last awhile or it could go **** up on in short order kinda hard to say.
Old 07-30-11, 10:28 PM
  #3  
Forever blown!

Thread Starter
iTrader: (14)
 
MuRCieLaGo's Avatar
 
Join Date: Jul 2007
Location: Trois-Rivieres (QC)
Posts: 1,370
Received 13 Likes on 10 Posts
Took it for a 10 kms ride. Now, my tranny feels like it's empty! I can't find any gear. Happened to anyone? I never saw this kind of problem...
Old 07-30-11, 10:39 PM
  #4  
Full Member
 
RotoryDreamer's Avatar
 
Join Date: Jul 2011
Location: Wisconsin
Posts: 51
Likes: 0
Received 0 Likes on 0 Posts
Where is your clutch taking up at top,mid,or bottom of pedal? Sounds like something broke or came loose in the shift linkage some where.
Old 07-30-11, 10:43 PM
  #5  
Forever blown!

Thread Starter
iTrader: (14)
 
MuRCieLaGo's Avatar
 
Join Date: Jul 2007
Location: Trois-Rivieres (QC)
Posts: 1,370
Received 13 Likes on 10 Posts
Mid, clutch has 6,000 kms. I achieved to find the 4th gear, otherwise I have NO gear, I can move the shifter everywhere with 0 restriction, like if it was empty. What did I break?
Old 07-30-11, 11:29 PM
  #6  
Full Member
 
RotoryDreamer's Avatar
 
Join Date: Jul 2011
Location: Wisconsin
Posts: 51
Likes: 0
Received 0 Likes on 0 Posts
I unfortunately don't know a lot about the FDs trans and my searches haven't turned up much that was useful. My guess is that it will be something in close proximity to the shifter like the shift select spindle or the end of the shifter actually being broken off.

I'd start by pulling the shifter out and seeing if you find anything that is broken or worn out looking.

It is also possible that you munched the 5th syncro and a piece went through and shredded the trans though I'd thing you would have felt that.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
The1Sun
New Member RX-7 Technical
5
09-15-15 04:45 PM
sinclair7seven
General Rotary Tech Support
11
09-11-15 10:15 AM
REX7&Z32TT
New Member RX-7 Technical
5
09-09-15 05:16 AM



Quick Reply: Tranny or clutch? 5th gear issue... *searched*.



All times are GMT -5. The time now is 06:26 PM.