3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Stuff I did on my FD today - What about yours?

Thread Tools
 
Search this Thread
 
Old Jul 31, 2012 | 07:07 PM
  #51  
1QWIK7's Avatar
White chicks > *
Tenured Member: 20 Years
iTrader: (33)
 
Joined: Jul 2003
Posts: 13,146
Likes: 1
From: Secaucus, New Jersey
Finally did my tranny fluid. Now just gotta do the diff.
Reply
Old Aug 16, 2012 | 12:14 AM
  #52  
scotty R's Avatar
Senior Member
Tenured Member 15 Years
iTrader: (13)
 
Joined: Jan 2009
Posts: 401
Likes: 1
From: niagara , ON
old gauges
[IMG][/IMG]
new ones

[IMG][/IMG]
new spec lights!!!
[IMG][/IMG]
[IMG][/IMG]

special thanks to mustangeater and fred
Reply
Old Aug 16, 2012 | 12:21 AM
  #53  
scotty R's Avatar
Senior Member
Tenured Member 15 Years
iTrader: (13)
 
Joined: Jan 2009
Posts: 401
Likes: 1
From: niagara , ON
love love these seats!!!do they slide back further on rails then the oem seats? my passenger seat doesnt seem to wanna go back that far even tho there is room, where did you end up picking them up from??



Originally Posted by Coverhag
Today I installed some RZ seats into my car. After sitting in them I think Mazda missed the mark by not putting them in a lot more cars. They are very comfortable and make much better use of the space in the cabin. As a 6'1" guy, I can stretch right out in the passenger side now.

These seats came out of car I recently bought to get some nice parts from. It was advertised as a Black RX-7. When I went to see it the fellow indicated it was some touring model with a larger gas tank. Somehow I keep from smiling to much and paid the man and loaded up the car. Kinda like the story of an ad in paper advertising an old chevrolet for sale and finding out it is a split window corvette. Turns out this is a Mines Motorsports tuned RZ that needs water seals.

I will admit, it does feel a bit sacrilegious pulling the RZ parts of it. Kinda like killing it somehow. But, someone will get a nice R1 equipped car out of it.

p.s.- car for sale in Canadian classifieds


Reply
Old Aug 17, 2012 | 02:16 AM
  #54  
Coverhag's Avatar
FD Addict
Tenured Member 05 Years
iTrader: (15)
 
Joined: Apr 2011
Posts: 156
Likes: 4
From: Alberta, Canada
AB

Thanks for your comments on the seats. I was lucky enough to come across a RZ here in Canada, only had to buy the whole car to get the seats! I'm not certain if these rails slide back further but the seats are certainly thinner than the r1 seats. Either way, I can barely reach the front foot area on the passenger side with the seat all the way back. Cheers!
Reply
Old Aug 17, 2012 | 09:20 AM
  #55  
r074r'/ |\|00B
Tenured Member 15 Years
iTrader: (14)
 
Joined: Jan 2002
Posts: 922
Likes: 0
From: KC, KS
Originally Posted by Coverhag
Thanks for your comments on the seats. I was lucky enough to come across a RZ here in Canada, only had to buy the whole car to get the seats! I'm not certain if these rails slide back further but the seats are certainly thinner than the r1 seats. Either way, I can barely reach the front foot area on the passenger side with the seat all the way back. Cheers!
Do you sit lower in these seats? Specifically, is there more room between your head & roof now?
Reply
Old Aug 17, 2012 | 10:13 AM
  #56  
powerhour's Avatar
Turbo Power
 
Joined: Jul 2009
Posts: 224
Likes: 1
From: Vancouver Island BC
Changed my oil and found out my turbo is leaking oil and my pillow bushings are shot, that's what I'll be doing tomorrow
Reply
Old Aug 17, 2012 | 06:43 PM
  #57  
zman600's Avatar
Senior Member
Tenured Member 15 Years
iTrader: (5)
 
Joined: Jan 2010
Posts: 320
Likes: 0
From: Katy (Houston)
got board today and had fun with an extra set of taillights in my garage.
i also did the lotta circles set for a forum member recently.

im keeping my 99 spec on my car but i might swap them out every once and a while

crappy cell phone makes them look bad up close...
Attached Thumbnails Stuff I did on my FD today - What about yours?-custom-2-taillights.jpg   Stuff I did on my FD today - What about yours?-custom-2-taillights-2.jpg   Stuff I did on my FD today - What about yours?-custom-1-taillights.jpg   Stuff I did on my FD today - What about yours?-custom-1-taillights-2.jpg   Stuff I did on my FD today - What about yours?-nadeem-taillights-stars.jpg  


Last edited by zman600; Aug 17, 2012 at 06:46 PM.
Reply
Old Dec 26, 2012 | 10:55 AM
  #58  
D.Adams's Avatar
Thread Starter
To each there own.
 
Joined: Apr 2012
Posts: 69
Likes: 1
From: Lake Havasu City, AZ
So i was having a little bit of a boost issue so i gave no ***** and tore her down to block to delete solenoid rack / parallel my enfini turbos / delete my emissions bs and clean the harness up.





Reply
Old Dec 27, 2012 | 08:05 PM
  #59  
jkstill's Avatar
Searching for 10th's
Tenured Member: 20 Years
Liked
Loved
Community Favorite
iTrader: (11)
 
Joined: May 2002
Posts: 2,279
Likes: 42
From: Portland OR
Originally Posted by 1QWIK7
This.

While that might be something i would say just to be a dick lol, you have a valid point.

My FD runs, runs great actually. Besides the shitty suspension and little nick nacks that i need to address, the car will go anywhere. Do i trust it? Prob not. I probably have a 50 mile limit per trip in case i get stuck somewhere, at least i wont be too far from home.

But apart for that, i can take my FD to work, but i wouldnt want to. The roads are terrible, the cops are dicks and in the parking lot, people park SUPER close to each other. So why would i?? Makes no sense.
Just now saw this - funny.

You mis-assumed what I had in mind.

I was thinking something more like the attached.

Everything works, and quite well.

Wouldn't drive it to work though.
Attached Thumbnails Stuff I did on my FD today - What about yours?-fd_at_national_tour-medium-.jpg  
Reply
Old Dec 30, 2012 | 09:08 PM
  #60  
TurboMazdaSpeed's Avatar
1.3L piston eater
Tenured Member 10 Years
 
Joined: Nov 2006
Posts: 514
Likes: 3
From: Vancouver, Canada
Thumbs up

Dat sound deadening removal



Reply
Old Dec 31, 2012 | 10:02 AM
  #61  
Copeland's Avatar
32psi+
Tenured Member: 15 Years
iTrader: (42)
 
Joined: Sep 2006
Posts: 1,323
Likes: 40
From: Raleigh, NC




Just took it out the paint booth, new front bumper and wheels.
Reply
Old Jan 1, 2013 | 02:41 AM
  #62  
fd3s777's Avatar
Registered User
Tenured Member 20 Years
iTrader: (3)
 
Joined: Aug 2003
Posts: 2,191
Likes: 0
From: NY<=>TW
Installed my Carbon Fiber RE GTII spoiler today.

Name:  B8553C96-D8B9-4917-9F98-9E2BCCFC0DD4-4338-000006BDA596E12A.jpg
Views: 108
Size:  66.8 KB
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
ZaqAtaq
New Member RX-7 Technical
2
Sep 5, 2015 08:57 PM




All times are GMT -5. The time now is 12:34 PM.