So how many people have done the Auto -> Manual Swap
#51
Lawn Ornament
Thread Starter
Originally posted by 1point3liter
Do any of you guys have a 3.9 auto rear end that you would like to get rid of?
Please PM me if you do.
I also have a manual drive shaft, 5 speed transmission, master/slave cylinders, and a 4.10 rear end I may want to get rid of.
Do any of you guys have a 3.9 auto rear end that you would like to get rid of?
Please PM me if you do.
I also have a manual drive shaft, 5 speed transmission, master/slave cylinders, and a 4.10 rear end I may want to get rid of.
#52
Rotary Enthusiast
Join Date: Dec 2001
Location: WILBURTON, OKLAHOMA
Posts: 773
Likes: 0
Received 0 Likes
on
0 Posts
I just want to remind everyone what the most import tool is for the swap. The big *** service manual. It is now my bible. If you don't have one get one before you try and tackle the swap.
#53
Rotary Enthusiast
Join Date: Dec 2001
Location: WILBURTON, OKLAHOMA
Posts: 773
Likes: 0
Received 0 Likes
on
0 Posts
Here is a tip for those that don't have the Service manual. You have to remove the four bolts that hold the torque convertor to the flexplate. That way you can drop the tranny with the covertor inside. There is not enough room to drop the tranny with the torque convertor still bolted to the flexplate. You get access to the four bolts through a service hole in the bottom from of the tranny. You remove a little cover and work through the hole. Take our a bolt and use a big flathead screw drive to turn the flexplate so you can get to the next one.
If the torque covertor is still stuck inside of the flexplate jack the tranny up a little higher, this will help brake in loose. The torque convertor sits about 1/4 inch inside of the flexplate and can get froze inside. Or you can try a pry bar, but this didn't work well for me.
I hope this helps someone.
Brady Mahoney
If the torque covertor is still stuck inside of the flexplate jack the tranny up a little higher, this will help brake in loose. The torque convertor sits about 1/4 inch inside of the flexplate and can get froze inside. Or you can try a pry bar, but this didn't work well for me.
I hope this helps someone.
Brady Mahoney
#54
Rotary Enthusiast
Join Date: Dec 2001
Location: WILBURTON, OKLAHOMA
Posts: 773
Likes: 0
Received 0 Likes
on
0 Posts
Has anyone had any Tuning issues after the swap? My car dies @ stop signs sometimes. I can't seem to tune it out. It is about to drive me nuts. And no I don't have a vacuum leak. And the damn thing smokes sometimes now. I am starting to wish I had left well enough alone.
#55
Originally posted by BRADYMAHONEY
Has anyone had any Tuning issues after the swap? My car dies @ stop signs sometimes. I can't seem to tune it out. It is about to drive me nuts. And no I don't have a vacuum leak. And the damn thing smokes sometimes now. I am starting to wish I had left well enough alone.
Has anyone had any Tuning issues after the swap? My car dies @ stop signs sometimes. I can't seem to tune it out. It is about to drive me nuts. And no I don't have a vacuum leak. And the damn thing smokes sometimes now. I am starting to wish I had left well enough alone.
#56
Rotary Enthusiast
Join Date: Dec 2001
Location: WILBURTON, OKLAHOMA
Posts: 773
Likes: 0
Received 0 Likes
on
0 Posts
Why my car was dying @ stop lights.
I got it figured out. My car kept trying to go into open loop down around my idle area of the map. I have my maps pretty lean there. This was not a problem with the auto, but maybe the prolight flywheel doesn't have enough enertia to keep things spinning. I just threw some more fuel in the mix down low and everything is OK.
#57
I got a question, Im in the middle of doing the swap right now and i'm kinda stuck on the stock counterwieght. Is there another way to get this off other that with the SST. Do i need to take it off. I have a ACT lightweight Flywheel with new counter weight, can i just use the one thats on there? Is there any difference between the ACT and factory one. Thanks.
#60
Thanks. looked the same but wanted to make sure. Another question, is there a trick to reinstalling the drive shafts?, I did what it told me in the manual but the ***** still wont go it all the way. i didnt replace the clips but they measure to what the should be. Any advice?
#63
Lawn Ornament
Thread Starter
Originally posted by GSXR0383
Differential to Wheel
Differential to Wheel
#65
Rotary Enthusiast
Join Date: Dec 2001
Location: WILBURTON, OKLAHOMA
Posts: 773
Likes: 0
Received 0 Likes
on
0 Posts
I have found that tapping the drive shafts in with a big hammer works best.
You can get it almost all the way in by hand, maybe about 3/8 of an inch out then I had to hit the drive shaft @ the hubs to get the rings to snap on in. I know at least one other member has done it this way too.
Brady Mahoney
You can get it almost all the way in by hand, maybe about 3/8 of an inch out then I had to hit the drive shaft @ the hubs to get the rings to snap on in. I know at least one other member has done it this way too.
Brady Mahoney
#66
Lawn Ornament
Thread Starter
Originally posted by BRADYMAHONEY
I have found that tapping the drive shafts in with a big hammer works best.
You can get it almost all the way in by hand, maybe about 3/8 of an inch out then I had to hit the drive shaft @ the hubs to get the rings to snap on in. I know at least one other member has done it this way too.
Brady Mahoney
I have found that tapping the drive shafts in with a big hammer works best.
You can get it almost all the way in by hand, maybe about 3/8 of an inch out then I had to hit the drive shaft @ the hubs to get the rings to snap on in. I know at least one other member has done it this way too.
Brady Mahoney
#68
Rotary Enthusiast
Join Date: Dec 2001
Location: WILBURTON, OKLAHOMA
Posts: 773
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by ejmack1
Yeah I used a rubber mallet to get mine in... i think there was three sides you can tap on, just do it evenly and it should slip in nicely.
Yeah I used a rubber mallet to get mine in... i think there was three sides you can tap on, just do it evenly and it should slip in nicely.
#71
All right the mechanical part is pretty much done other then the stupid 10 dollar hard-line for the clutch which wont be here till Wednesday or Thursday, so now the electrical till then. I know this has been discussed in a few different threads but I haven't found it all in one place. I've pieced together a few things. So let me know if the information I have is correct and what im missing: connect pins 8 & 9 on the inhibitor switch harness to get the car to start. and cut the blue/white wire @ pin G on the Cruise control ECU connector for the cruse control. Now ive glanced at the manual and it tells me what pins go to what switch. so do I just add wires to the harness and run them to the transmission and make my own connection? Or are the wires already ran down there? Just trying to get all the information in one place. Sorry for being a little lazy and not tracing the wires but im taking a break from the car for tonight. about 36 hours already, need sleep, food, and to get all this **** off me(ATF,oil, brake fluid, gas, and grease).
hey also the lines from the auto tranny going to the oil cooler. Can i remove the oil cooler since they wont be connected to the tranny anymore? Or dose it serve another purpose, didn't see anything in the manual.
hey also the lines from the auto tranny going to the oil cooler. Can i remove the oil cooler since they wont be connected to the tranny anymore? Or dose it serve another purpose, didn't see anything in the manual.
#73
Alright i need some help on the electrical side of this swap. I connect pins 8 & 9 on the inhibitor switch harness to get the car to start. and cut the blue/white wire @ pin G on the Cruise control ECU connector for the cruse control. Correct? Now do i need to run any wires or can i find the wires i need to hook up to the manual tranny already down there(ex 1-2 switch, reverse switch, netual switch, ect). I know i need to run the clutch switch.
Just found the clutch line at Peboys, so i should have this done tonight.
Just found the clutch line at Peboys, so i should have this done tonight.