SBC-ID Boost controller problem.
#1
Rotary Enthusiast
Thread Starter
SBC-ID Boost controller problem.
Hey everyone, the orginal thread started here with my original boost problem.
Take a look please if its not too much trouble
https://www.rx7club.com/showthread.p...5&pagenumber=1
Anyway, After I got my midpipe on, I put the Boost setting to 0 with the gain setting at like 15 in manual mode.
For some reason I got that problem in the thread. I managed to lower the gain to 13 and dial out creep to 12psi. However, it seems my boost controller, or my boost controller settings were wrong.
Would anyone be willing to share their settings that have a midpipe or similar mods? Also would anyone be able to show me a picture of how they connected the boost controller? I was having a problem before getting full boost on primary. I'm thinking its possible my boost controller is just messed up, but I'd like any clarification that I could get.
Please I'd appreciate anyones time if they could help me out
Mods are
Intake DP, MP, CB Boost controller, PFC commanderless, Efini y-pipe and pullies for power mods.
Steve
Take a look please if its not too much trouble
https://www.rx7club.com/showthread.p...5&pagenumber=1
Anyway, After I got my midpipe on, I put the Boost setting to 0 with the gain setting at like 15 in manual mode.
For some reason I got that problem in the thread. I managed to lower the gain to 13 and dial out creep to 12psi. However, it seems my boost controller, or my boost controller settings were wrong.
Would anyone be willing to share their settings that have a midpipe or similar mods? Also would anyone be able to show me a picture of how they connected the boost controller? I was having a problem before getting full boost on primary. I'm thinking its possible my boost controller is just messed up, but I'd like any clarification that I could get.
Please I'd appreciate anyones time if they could help me out
Mods are
Intake DP, MP, CB Boost controller, PFC commanderless, Efini y-pipe and pullies for power mods.
Steve
#3
block-spike
Join Date: Feb 2004
Location: West Chester, PA
Posts: 548
Likes: 0
Received 0 Likes
on
0 Posts
I'll try to check mine when I go to lunch, just curious...you do have your control set to actuator not wastegate right?
Bob
and what do you mean by CB boost controller?
Bob
and what do you mean by CB boost controller?
Last edited by rdavidsrx7; 05-20-04 at 11:19 AM.
#5
block-spike
Join Date: Feb 2004
Location: West Chester, PA
Posts: 548
Likes: 0
Received 0 Likes
on
0 Posts
set for manual
set at 55
gain is 3
with this I see 12.5 with the gutted cat, and 13.5 with 3" midpipe
good luck, if ya need anything else feel free to pm me as I don't check this section often anymore
Bob
set at 55
gain is 3
with this I see 12.5 with the gutted cat, and 13.5 with 3" midpipe
good luck, if ya need anything else feel free to pm me as I don't check this section often anymore
Bob
Trending Topics
#8
Perpetual Rebuilder
I run my gain at 45-50. Of course I have a single so that might change everything...
I still havent spent much time tuning it yet but it runs fine at this level. I never see a spike of any type...Always a flat line at the boost level I set.
Shawn
www.3rdgenrx7.com
I still havent spent much time tuning it yet but it runs fine at this level. I never see a spike of any type...Always a flat line at the boost level I set.
Shawn
www.3rdgenrx7.com
#9
Rotary Enthusiast
Thread Starter
Thanks everyone for the settings. Im worried my boost controller might actually be F'd.
Anyone else have settings? the more the merrier!(sp)
Steve
Anyone else have settings? the more the merrier!(sp)
Steve
Thread
Thread Starter
Forum
Replies
Last Post
Skeese
Adaptronic Engine Mgmt - AUS
65
03-28-17 03:30 PM