Need New Engine
#1
I Like Guns
Thread Starter
iTrader: (5)
Join Date: Mar 2002
Location: Bismarck, ND
Posts: 512
Likes: 0
Received 0 Likes
on
0 Posts
Need New Engine
OK guys heres the story.
I bought a car from a kid in Texas and he told me the turbos were out on the car. So I asked what happened. He said that one day he was driving around and all of a sudden no boost. So he shut the car off and towed it home. I asked if anything was wrong with the engine and he said no. He said he had the engine and turbos rebuilt about 20 K ago. He then said that he had a compression test and both rotors were good.
So I bought the car and planned on putting a single turbo on it. So I got the car put a XS single on it PFC, fuel pump, 1300cc injectors, AVC-R, and a lot of other goodies. Then I was ready to go I did a fast compression test and it only had about 20 psi in the rear rotor. So I read on the internet that if a car has sat for a while the seals might have relaxed so I did the ATF trick and nothing. So I did a compression test on the front rotor and it had about 90 psi. So I spoke to a guy at Rotary Performance and he said that the seals are gone. So he said to buy a new engine through the Mazda dealer.
But do you guys know another place to buy a new engine what might be cheaper. The Mazda dealer can get me one for about $2200 . Any advice would be appreciated.
I bought a car from a kid in Texas and he told me the turbos were out on the car. So I asked what happened. He said that one day he was driving around and all of a sudden no boost. So he shut the car off and towed it home. I asked if anything was wrong with the engine and he said no. He said he had the engine and turbos rebuilt about 20 K ago. He then said that he had a compression test and both rotors were good.
So I bought the car and planned on putting a single turbo on it. So I got the car put a XS single on it PFC, fuel pump, 1300cc injectors, AVC-R, and a lot of other goodies. Then I was ready to go I did a fast compression test and it only had about 20 psi in the rear rotor. So I read on the internet that if a car has sat for a while the seals might have relaxed so I did the ATF trick and nothing. So I did a compression test on the front rotor and it had about 90 psi. So I spoke to a guy at Rotary Performance and he said that the seals are gone. So he said to buy a new engine through the Mazda dealer.
But do you guys know another place to buy a new engine what might be cheaper. The Mazda dealer can get me one for about $2200 . Any advice would be appreciated.
#4
You would also need to prove mis-representation. Not unless he actually provided to you something in writing....that states the fact. Also, your purchased it in another state...
Trending Topics
#8
Lurking..................
Join Date: Mar 2001
Location: PA
Posts: 2,220
Likes: 0
Received 0 Likes
on
0 Posts
www.aktkinsrotary.com for a rebuild, but I believe they just take your old one as a core, and give you one they already built, not sure.
www.rotaryengine.com for a rebuild
For a reman, Malloy Mazda like someone said would probably be the cheapest.
www.rotaryengine.com for a rebuild
For a reman, Malloy Mazda like someone said would probably be the cheapest.
Last edited by black99; 06-09-02 at 02:42 PM.
#9
Old School Member
Join Date: Feb 2001
Location: Vancouver, Wa, USA
Posts: 640
Likes: 0
Received 0 Likes
on
0 Posts
#10
Rotary Enthusiast
Join Date: Feb 2001
Location: Calgary, Alberta, Canada
Posts: 809
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
KAL797
Test Area 51
0
08-11-15 03:47 PM