My baby is sick!!!!
#1
Newbie
Thread Starter
Join Date: Nov 2002
Location: Abquerque,NM
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
My baby is sick!!!!
Hey guys i need help on my Rex. She caught a cold or something. Today i was doing a little day cruisin enjoying the cloudy day in New Mexico. As i stoped at a friends house and tried to start my FD she would not start. It sounds likes she wants to start but its like she is not getting enough gas. I have checked the spark and plugs along with the fuel pump. every thing on that end looks great. Some say it might be my ECU, a cracked Apex seal or an ingector might be open. I need help!!!!
#2
I Sold My Car 2 the Devil
Join Date: Oct 2001
Location: Duncanville, Tx
Posts: 2,361
Likes: 0
Received 0 Likes
on
0 Posts
when you pulled the plugs were they wet? ...try pulling your EGI fuse (big one under the hood by batt.) have the car jumped to another car thats running... then crank for a few.... 10 sec. maybe... then hook the bus fuse back up and give it a crank... could be flooded... worst could be blown... normally the motor will start on a blown motor though... if that does not work lookup flooding and there will be a link on how to get it started again if the plugs were wet.
-Ryker
-Ryker
#3
Full Member
Join Date: Feb 2002
Location: Where Uncle Sam sends me
Posts: 162
Likes: 0
Received 0 Likes
on
0 Posts
Ain't got no gas in it.........(Slingblade)
Mapsensor
Could try resetting ECU
Check all your fuses
Or its flooded
Mapsensor
Could try resetting ECU
Check all your fuses
Originally Posted by wonder1and
when you pulled the plugs were they wet? ...try pulling your EGI fuse (big one under the hood by batt.) have the car jumped to another car thats running... then crank for a few.... 10 sec. maybe... then hook the bus fuse back up and give it a crank... could be flooded... worst could be blown... normally the motor will start on a blown motor though... if that does not work lookup flooding and there will be a link on how to get it started again if the plugs were wet.
-Ryker
-Ryker
Last edited by wylie; 11-16-04 at 01:01 AM.
#4
I am so smrt.
Join Date: Aug 2003
Location: Torrance, CA
Posts: 886
Likes: 0
Received 0 Likes
on
0 Posts
enfinirx7-
if it was your apex seals you would notice some bad idle before you shut the car off. is the motor cranking at all? do you hear any clicking when you try and start... need a few more details. I would say get the compression test done and ask also for a water pressure test. other then that try not to worry too much about it. i hope it turns out to be nothing serious.
ian
if it was your apex seals you would notice some bad idle before you shut the car off. is the motor cranking at all? do you hear any clicking when you try and start... need a few more details. I would say get the compression test done and ask also for a water pressure test. other then that try not to worry too much about it. i hope it turns out to be nothing serious.
ian
#5
Republican and proud
Join Date: Nov 2003
Location: PHILLY
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
If you have no clue what it could be, the first thing to do is see if any engine codes come up. If you car was running fine, then just wouldn't start, I'm sure it's probably a bad wire connection or sensor. I doubt your engine is blown, esspecially if there were no problems before you turned off the car. The engine codes will help you pin-point the problem. You can jump the grounds in the diagnostic terminal to get any codes.
Thread
Thread Starter
Forum
Replies
Last Post