3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Mounting the Undertray

Thread Tools
 
Search this Thread
 
Old Mar 18, 2009 | 10:02 AM
  #1  
milano maroon's Avatar
Thread Starter
Senior Member
Tenured Member: 15 Years
iTrader: (1)
 
Joined: Jul 2008
Posts: 279
Likes: 2
From: Los Alamos, NM
Mounting the Undertray

My car didn't come with one but I want to install an undertray. What does the front lip of the undertray bolt to? From looking at the parts manual it looks like it might a flange along the bottom of the front bumper.

Thanks,

Jeff
Reply
Old Mar 18, 2009 | 10:18 AM
  #2  
RA8225's Avatar
Banned
iTrader: (6)
 
Joined: Jul 2003
Posts: 7,141
Likes: 46
The undertray bolts on to the front lip of your car. Well if you have a front lip that is
Reply
Old Mar 18, 2009 | 10:30 AM
  #3  
Sgtblue's Avatar
Urban Combat Vet
Tenured Member: 20 Years
Liked
Loved
Community Favorite
iTrader: (16)
 
Joined: Oct 2003
Posts: 12,160
Likes: 983
From: Mid-west
There are about 6 bolts along the leading edge just under the front lip that go into captured nuts on the lower edge of the bumper. Four more (two on each side) that are recessed around the AC condensor lines etc. just aft. The last two bolts are on the trailing edge into the cross-member. All are 10mm. There are also two 'ears' on the trailing edge that use a push-fastener into the cross-member. The fasteners area similar to the ones that anchor the front of the hatch carpet.
Reply
Old Mar 18, 2009 | 10:36 AM
  #4  
milano maroon's Avatar
Thread Starter
Senior Member
Tenured Member: 15 Years
iTrader: (1)
 
Joined: Jul 2008
Posts: 279
Likes: 2
From: Los Alamos, NM
Thank you for the reply.

So if you have an aftermarket bumper that does not have a flange with bolt holes at the bottom for a front lip does that mean you cannot use the undertray?

What would normally be the front lip (such as an R1 lip) which you bolt onto the bumper is molded into the aftermarket bumper.

Then what do you do (or not do)?
Reply
Old Mar 18, 2009 | 11:26 AM
  #5  
jasonn's Avatar
Half Triangle
Tenured Member: 15 Years
iTrader: (10)
 
Joined: Mar 2009
Posts: 408
Likes: 2
From: Walnut, CA
Shine has a undertray for aftermarket.
Reply
Old Mar 18, 2009 | 11:39 AM
  #6  
Smitter's Avatar
94 Single Turbo FD
Tenured Member: 15 Years
 
Joined: May 2006
Posts: 1,418
Likes: 1
From: Calgary, Alberta, Canada
you should be able to bolt the stock under tray up to a car with an aftermarket bumper.
I ran my undertray with a cwest front end. I did not bolt the undertray to the front lip however.

The tray was sturdy enough without the bolts along the front, and the leading edge of the undertray kinda tucked into the larger lower lip of the cwest front end. it worked fine.

i would highly recomend installing the undertray because it helps direct air through the radiator of the car, of course leading to cooler water temps.
Reply
Old Mar 19, 2009 | 10:12 AM
  #7  
milano maroon's Avatar
Thread Starter
Senior Member
Tenured Member: 15 Years
iTrader: (1)
 
Joined: Jul 2008
Posts: 279
Likes: 2
From: Los Alamos, NM
Thanks everyone for the replies. One last question then. With the stock bumper does the undertray and an R1 lip share the same monting bolts?

Jeff
Reply
Old Mar 19, 2009 | 10:45 AM
  #8  
Sgtblue's Avatar
Urban Combat Vet
Tenured Member: 20 Years
Liked
Loved
Community Favorite
iTrader: (16)
 
Joined: Oct 2003
Posts: 12,160
Likes: 983
From: Mid-west
Originally Posted by milano maroon
Thanks everyone for the replies. One last question then. With the stock bumper does the undertray and an R1 lip share the same monting bolts?

Jeff
Yes.
Reply
Old Mar 19, 2009 | 05:59 PM
  #9  
badddrx7's Avatar
All Spooled Up
Tenured Member 15 Years
iTrader: (7)
 
Joined: Nov 2001
Posts: 2,752
Likes: 3
From: Ironton,ohio
With an aftermarket you fab up an insert to bolt it up. Sheet aluminum works

later
Reply
Old Mar 19, 2009 | 10:36 PM
  #10  
milano maroon's Avatar
Thread Starter
Senior Member
Tenured Member: 15 Years
iTrader: (1)
 
Joined: Jul 2008
Posts: 279
Likes: 2
From: Los Alamos, NM
Could you give me a little more information on the insert you mentioned?
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
freq
2nd Generation Specific (1986-1992)
4
Sep 7, 2015 04:35 PM
SakeBomb Garage
SakeBomb Garage
0
Sep 4, 2015 05:20 PM
SakeBomb Garage
Vendor Classifieds
0
Sep 4, 2015 05:19 PM




All times are GMT -5. The time now is 03:11 AM.