3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Help Troubleshoot Bucking

Thread Tools
 
Search this Thread
 
Old 10-21-13, 11:22 PM
  #1  
Jon R.

Thread Starter
iTrader: (1)
 
jon4825's Avatar
 
Join Date: Mar 2007
Location: Ashburn, VA
Posts: 185
Likes: 0
Received 0 Likes on 0 Posts
VA Help Troubleshoot Bucking

I searched the forum for jerking or bucking during deceleration and the results are all over the place.

Can someone help me put together a plan on how to trouble the issue?

While decelerating in gear at both low and highspeeds the rear end starts to jerk and buck. It does not stop until I either accelrate or put the clutch it. It happens when I am at 65 mph and braking.

My search results stated it could be TPS, Dashpot, Differential Mount, etc.

I definitely feels like a drivetrain issue like the rear end or transmission needs to be braced to keep it from jerking back and forth. I am really posing the question because I dont understand how a TPS or Dashpot could cause this issue.

Thanks for the help in advance,

Jon
Old 10-22-13, 06:45 AM
  #2  
Rotary Specialists
RX7Club Vendor
iTrader: (11)
 
Banzai-Racing's Avatar
 
Join Date: Jan 2008
Location: Indiana
Posts: 4,824
Received 307 Likes on 179 Posts
You have a microtech, do you have the decel fuel cut set up?
Old 10-22-13, 07:22 AM
  #3  
Senior Member

iTrader: (5)
 
t2ae's Avatar
 
Join Date: Apr 2006
Location: durham, NC
Posts: 527
Received 2 Likes on 2 Posts
tps could easily cause all types of bucking and jerking. just be sure its in spec
Old 10-22-13, 09:23 AM
  #4  
Jon R.

Thread Starter
iTrader: (1)
 
jon4825's Avatar
 
Join Date: Mar 2007
Location: Ashburn, VA
Posts: 185
Likes: 0
Received 0 Likes on 0 Posts
Thanks for the microtech advise on the decel fuel setup. I will also search on how to diagnose a TPS. Car is in the body shop so I will post update in a couple days.
Old 10-28-13, 08:28 PM
  #5  
Searching for 10th's

iTrader: (11)
 
jkstill's Avatar
 
Join Date: May 2002
Location: Portland OR
Posts: 2,247
Received 29 Likes on 18 Posts
+1 - Adjusting the TPS 100% fixed that issue in my FD.
Old 10-28-13, 09:23 PM
  #6  
Sponsor
iTrader: (41)
 
IRPerformance's Avatar
 
Join Date: Apr 2003
Location: NJ
Posts: 11,347
Received 318 Likes on 190 Posts
Diff bushings, motor mounts, pillow *****. As said above, check your deccel fuel cut too. Should be below 1400 in most cases.
Old 10-30-13, 06:42 AM
  #7  
Rotary Specialists
RX7Club Vendor
iTrader: (11)
 
Banzai-Racing's Avatar
 
Join Date: Jan 2008
Location: Indiana
Posts: 4,824
Received 307 Likes on 179 Posts
Microtech is a vacuum set point actuated decel fuel cut.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
93FD510
New Member RX-7 Technical
2
10-01-15 02:00 PM



Quick Reply: Help Troubleshoot Bucking



All times are GMT -5. The time now is 12:29 AM.