RX7Club.com - Mazda RX7 Forum

3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:
Full Detail Automotive

Is this the correct position of the pre-spool for non seq?

Thread Tools
 
Search this Thread
 
Old Apr 5, 2005 | 05:34 PM
Share
  #1  
Fatman0203's Avatar
Fatman0203
Thread Starter
Eats, Sleeps, Dreams Rotary
Tenured Member 05 Years
 
Joined: May 2003
Posts: 3,639
Likes: 0
From: MIA
Is this the correct position of the pre-spool for non seq?
Or did I weld it the wrong way? BTW is the wastegate there closed or open?
Thanks!

Reply
0
Old Apr 5, 2005 | 06:44 PM
Share
  #2  
Fatman0203's Avatar
Fatman0203
Thread Starter
Eats, Sleeps, Dreams Rotary
Tenured Member 05 Years
 
Joined: May 2003
Posts: 3,639
Likes: 0
From: MIA
Bump ^
Reply
0
Old Apr 5, 2005 | 06:46 PM
Share
  #3  
RX7WEEE's Avatar
RX7WEEE
Need a 20b FD.
Tenured Member 15 Years
iTrader: (16)
 
Joined: Feb 2003
Posts: 1,946
Likes: 1
From: Bellingham Wa
Yeah, I'm 90% sure you got it correct.
Reply
0
Old Apr 5, 2005 | 08:09 PM
Share
  #4  
jimlab's Avatar
jimlab
Super Snuggles
Tenured Member 20 Years
 
Joined: Feb 2001
Posts: 10,091
Likes: 34
From: Redmond, WA
This picture shows the correct location of the pre-control gate... gone.

Reply
0
Old Apr 5, 2005 | 08:24 PM
Share
  #5  
Fatman0203's Avatar
Fatman0203
Thread Starter
Eats, Sleeps, Dreams Rotary
Tenured Member 05 Years
 
Joined: May 2003
Posts: 3,639
Likes: 0
From: MIA
Originally Posted by jimlab
This picture shows the correct location of the pre-control gate... gone.
I knew someone would mention that, I got everything fixed and its running quite nice.
Thanks guys.
Reply
0
Old Apr 5, 2005 | 09:01 PM
Share
  #6  
CourageOO7's Avatar
CourageOO7
Full Member
Tenured Member 05 Years
 
Joined: Aug 2003
Posts: 203
Likes: 0
From: Maryland
well, tie it off that way...if you only get 7psi of boost you got it wrong! :O) IF I remember correctly, the end of the hinge should be closer to the rear of the car...think that's the way you have it.
Reply
0
Old Apr 5, 2005 | 09:02 PM
Share
  #7  
CourageOO7's Avatar
CourageOO7
Full Member
Tenured Member 05 Years
 
Joined: Aug 2003
Posts: 203
Likes: 0
From: Maryland
Good!
Reply
0
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
My first rotary almost caught fire...plan for it not to happen again
ls1swap
3rd Generation Specific (1993-2002)
17
Jun 3, 2024 03:25 PM
84SE Engine Swap Success! Surge at idle, clutch out.
LongDuck
1st Generation Specific (1979-1985)
12
Oct 7, 2015 08:12 PM
Airpump Compatible EFR IWG Single Turbo System
Turblown
Single Turbo RX-7's
1
Sep 30, 2015 05:58 PM
Back to Subforum
3rd Generation Specific (1993-2002)
View Next Unread
Boost Gauge




Advanced Search

All times are GMT -5. The time now is 06:53 AM.