Upgrading spark plugs
#1
Full Member
Thread Starter
Join Date: May 2006
Location: Texas
Posts: 136
Likes: 0
Received 0 Likes
on
0 Posts
Upgrading spark plugs
I'm about to do a full tune up and I figure I need to change my plugs (also to maybe combat the horrible mileage I've been getting)- does anyone have any ideas about what to use for an upgrade? Brands, type, anything.
Thanks!
Thanks!
Last edited by TetsuKatana; 10-10-06 at 07:40 PM.
#2
Rotary Enthusiast
Join Date: Jun 2003
Location: Ottawa, Canada
Posts: 874
Likes: 0
Received 0 Likes
on
0 Posts
Stock is best unless you have an upgraded turbo car or race car. People also sometimes like running the BR9EIX series iridium plugs for durability, however they are quite annoying to install. These cost the same as stock plugs.
#3
Strength and Honor
Join Date: Apr 2006
Location: CA bay area
Posts: 391
Likes: 0
Received 0 Likes
on
0 Posts
NGK! How hard do you drive? Do you race (i.e. above 7k rpm constantly)? The recommended plugs are as follows:
"Around town"
Leading: BUR6EQ
Trailing: BUR8EQ
Stock plugs, turbo and n/a (may be too cold for around town)
Leading: BUR7EQ
Trailing: BUR9EQ
There's basically no reason to not use one of those combinations, unless you have a monster race engine. Those come from here:
http://howto.globalvicinity.com/gv_w...i=62&co=1&vi=1
(if anyone has improvements, modify that page)
"Around town"
Leading: BUR6EQ
Trailing: BUR8EQ
Stock plugs, turbo and n/a (may be too cold for around town)
Leading: BUR7EQ
Trailing: BUR9EQ
There's basically no reason to not use one of those combinations, unless you have a monster race engine. Those come from here:
http://howto.globalvicinity.com/gv_w...i=62&co=1&vi=1
(if anyone has improvements, modify that page)
#5
FD pro licensed driver
iTrader: (3)
Join Date: Feb 2006
Location: Renton/Bellevue/Seattle WA
Posts: 2,897
Likes: 0
Received 2 Likes
on
2 Posts
Originally Posted by stevej88na
NGK! How hard do you drive? Do you race (i.e. above 7k rpm constantly)? The recommended plugs are as follows:
"Around town"
Leading: BUR6EQ
Trailing: BUR8EQ
Stock plugs, turbo and n/a (may be too cold for around town)
Leading: BUR7EQ
Trailing: BUR9EQ
There's basically no reason to not use one of those combinations, unless you have a monster race engine. Those come from here:
http://howto.globalvicinity.com/gv_w...i=62&co=1&vi=1
(if anyone has improvements, modify that page)
"Around town"
Leading: BUR6EQ
Trailing: BUR8EQ
Stock plugs, turbo and n/a (may be too cold for around town)
Leading: BUR7EQ
Trailing: BUR9EQ
There's basically no reason to not use one of those combinations, unless you have a monster race engine. Those come from here:
http://howto.globalvicinity.com/gv_w...i=62&co=1&vi=1
(if anyone has improvements, modify that page)
So just to clerify for someone that is a complete idiot and takes it to 7+K every chance he can (me) , you would recommend
Leading: BUR6EQ
Trailing: BUR8EQ
? I have an 88 n/a 90 compression :0P
#6
Strength and Honor
Join Date: Apr 2006
Location: CA bay area
Posts: 391
Likes: 0
Received 0 Likes
on
0 Posts
I've been going with MazdaTrix's recommended plugs (they supplied the list I gave), and even though I drive spiritedly too, I've found the BUR7EQ/BUR9EQ option fouls faster than the BUR6EQ/BUR8EQ option I'm running now.
Trending Topics
#8
Full Member
Join Date: Feb 2006
Location: Massachusetts
Posts: 169
Likes: 0
Received 0 Likes
on
0 Posts
My friend told me that it was actually best just to stick with the stock plugs unless you've really changed a lot of the car. He figures the engineers would have picked the best plug for the engine.
#11
Rotary Enthusiast
Join Date: Jun 2003
Location: Ottawa, Canada
Posts: 874
Likes: 0
Received 0 Likes
on
0 Posts
When my T2 was slightly modded I was running 4x BUR9EQ. Then I started running 4x BR9EIX. Worked great and the plugs last forever. May as well go to colder plugs if you are gonna be pushing the stock EFI.
#12
Strength and Honor
Join Date: Apr 2006
Location: CA bay area
Posts: 391
Likes: 0
Received 0 Likes
on
0 Posts
Just go the stock 7/9 route for now. You can inspect the plugs later and see how fouled they are. If they foul early, it may be because they’re too cold for your driving style. That’s why I switched to the 6/8 combo, which has worked well for me.
edit: nik's suggestion is good too, might be good to listen to a turbo guy!
edit: nik's suggestion is good too, might be good to listen to a turbo guy!
Last edited by stevej88na; 10-10-06 at 10:46 PM.
#13
Full Member
Join Date: May 2005
Location: East Oregon
Posts: 102
Likes: 0
Received 0 Likes
on
0 Posts
I run 7/9 in my vert, with it ported.
I just changed the plugs recently with ngk plats, so I'll know soon enough (round town 99%, with a little long distance highway driving 1%) on the fouling issue.
I just wanted to say two things:
One, definitely stick with ngk. good plugs.
Two, the point some people make about the engineers, and the best parts. Now, this sounds great in theory, but many factors go into manufacturing a car, and putting it all together. The most important factor being cost.
If the engineers had their way, only the best components would be used, and nothing would be "sub-standard." However, as many can attest (I being from the comp industry), doing things the right way is not the same as doing things the economic way.
Some parts cost more, some manufacturing processes cost more. In our economic system, that's how things work. To think that everything would be perfectly made, designed, and thought out is idealistic at best.
And, if you people need an example, here's one: the electronic systems in our cars. If the electronics were done as high quality as everyone would assume, why are there problem areas such as the logicon, headlight/wiper switches, etc.?
Just goes to show you, assumption is the mother of all f*ck ups.
I just changed the plugs recently with ngk plats, so I'll know soon enough (round town 99%, with a little long distance highway driving 1%) on the fouling issue.
I just wanted to say two things:
One, definitely stick with ngk. good plugs.
Two, the point some people make about the engineers, and the best parts. Now, this sounds great in theory, but many factors go into manufacturing a car, and putting it all together. The most important factor being cost.
If the engineers had their way, only the best components would be used, and nothing would be "sub-standard." However, as many can attest (I being from the comp industry), doing things the right way is not the same as doing things the economic way.
Some parts cost more, some manufacturing processes cost more. In our economic system, that's how things work. To think that everything would be perfectly made, designed, and thought out is idealistic at best.
And, if you people need an example, here's one: the electronic systems in our cars. If the electronics were done as high quality as everyone would assume, why are there problem areas such as the logicon, headlight/wiper switches, etc.?
Just goes to show you, assumption is the mother of all f*ck ups.
Thread
Thread Starter
Forum
Replies
Last Post