Turn signals failed?
09-09-05, 05:53 AM
#1
White Comet
Thread Starter
Join Date: Jan 2002
Location: Orange County
Posts: 2,145
Likes: 0
Received 0 Likes
on
0 Posts
Turn signals failed?
So today I was driving to school when i noticed the left turn signal blinking erratically. I couldnt tell if this was just glare or the signal but it went away.
So later in the evening it happens again and I can tell its the signal. I try hitting the left and right arm but no good. When I touch the hazards it goes away. Then I hit a bump in the road and it comes back and I hit the hazards again and it goes away. Now my turn signals won't work. I can hear it click but no lights. Any ideas on where to begin or what could cause this? Thanks!
So later in the evening it happens again and I can tell its the signal. I try hitting the left and right arm but no good. When I touch the hazards it goes away. Then I hit a bump in the road and it comes back and I hit the hazards again and it goes away. Now my turn signals won't work. I can hear it click but no lights. Any ideas on where to begin or what could cause this? Thanks!
09-09-05, 08:06 AM
#2
Former Moderator. RIP Icemark.
when you say erracticly do you just mean flashing fast (which once again would be the CPU indicating a bulb failure or short) or do you really mean erracticly as in no pattern (which would indicate a CPU failure and the CPU's flasher board would need to be replaced.
And I do have rebuilt CPU flasher boards available on my website
And I do have rebuilt CPU flasher boards available on my website
09-09-05, 09:23 AM
#3
White Comet
Thread Starter
Join Date: Jan 2002
Location: Orange County
Posts: 2,145
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for giving your input on this one.
I mean like really erratically as in like left then right or both together blinking in different variations of fast.
Where is the CPU located? You don't think it could be some wiring short in the actual gauge consoles wiring or is this commonly associated with what you named? Thanks again.
I mean like really erratically as in like left then right or both together blinking in different variations of fast.
Where is the CPU located? You don't think it could be some wiring short in the actual gauge consoles wiring or is this commonly associated with what you named? Thanks again.
09-09-05, 09:27 AM
#4
Former Moderator. RIP Icemark.
well again. if you have a bad bulb then the side with the bad bulb would be flashing faster than the side without the bad bulb.
the CPU is the black box next to the fuse box in the driver's kick panel
the CPU is the black box next to the fuse box in the driver's kick panel
09-09-05, 09:29 AM
#5
White Comet
Thread Starter
Join Date: Jan 2002
Location: Orange County
Posts: 2,145
Likes: 0
Received 0 Likes
on
0 Posts
No they were flashing without me touching any controls that have to do with them. Im pretty familiar with how the bad bulb flash is and this was a bit different.
Trending Topics
09-09-05, 01:57 PM
#10
Senior Member
my left turn signal works fine, left one doesnt work at all no light inside or out. hazards on the left one only works. is that the switch?
on a similar note my brights will flash but wont stay on
on a similar note my brights will flash but wont stay on
09-09-05, 02:20 PM
#11
Former Moderator. RIP Icemark.
Originally Posted by slow_2ed_gen
my left turn signal works fine, left one doesnt work at all no light inside or out. hazards on the left one only works. is that the switch?
on a similar note my brights will flash but wont stay on
on a similar note my brights will flash but wont stay on
Thread
Thread Starter
Forum
Replies
Last Post
The1Sun
1st Generation Specific (1979-1985)
7
09-18-15 07:13 PM