Short Shift ????
#4
Seduced by the DARK SIDE
Join Date: Apr 2001
Location: Orange Park FL (near Jax)
Posts: 7,323
Likes: 0
Received 2 Likes
on
2 Posts
I just cut the stock lever about 1" shorter.
Then I drilled a wood shift ball so it would fit tight & sit low on the lever.
A short piece of heater hose cover the hot steel lever.
The throw distance ends up about the same as a short shifter.
Here is my current console:
Then I drilled a wood shift ball so it would fit tight & sit low on the lever.
A short piece of heater hose cover the hot steel lever.
The throw distance ends up about the same as a short shifter.
Here is my current console:
#6
Locust of the apocalypse
Join Date: Apr 2003
Location: Directly above the center of the earth (York, PA)
Posts: 2,553
Likes: 0
Received 1 Like
on
1 Post
Ya know Higgi... why don't you just send me a parts list so i don't keep stepping on your dick when i post!!!!!!
Cutting the shifter down is the Ghetto way to do it, but it does shorten the lenght of travel, but it will make it a bit harder to shift. I'm actually thinking about cutting the shaft on my Mazdatrix Ssort Shifter and re-machining it to accept the stock shifter.
PS...... OH MY GOD IS THAT A CB??????????????????????????????????? :O
Cutting the shifter down is the Ghetto way to do it, but it does shorten the lenght of travel, but it will make it a bit harder to shift. I'm actually thinking about cutting the shaft on my Mazdatrix Ssort Shifter and re-machining it to accept the stock shifter.
PS...... OH MY GOD IS THAT A CB??????????????????????????????????? :O
Trending Topics
#9
Seduced by the DARK SIDE
Join Date: Apr 2001
Location: Orange Park FL (near Jax)
Posts: 7,323
Likes: 0
Received 2 Likes
on
2 Posts
Originally Posted by YearsOfDecay
PS...... OH MY GOD IS THAT A CB??????????????????????????????????? :O
If I push the radio to 10 watts & overdrive the linear, it broadbands enough to talk to nearby cops.
(Anonymous transmission) " Did you see how fast that Honda was going? "
#11
Seduced by the DARK SIDE
Join Date: Apr 2001
Location: Orange Park FL (near Jax)
Posts: 7,323
Likes: 0
Received 2 Likes
on
2 Posts
Originally Posted by Gatlin
I love that wood ball, that's awesome. I've always wanted to use wood in my car somehow. And it would wear nicely over time!
The only problem is, they come with a #10-32 set screw.
Drilling the wood to fit the shift lever threads & retapping the set screw to 1/4-20 makes it real solid.
Last edited by SureShot; 10-15-04 at 12:33 PM.
#12
Seduced by the DARK SIDE
Join Date: Apr 2001
Location: Orange Park FL (near Jax)
Posts: 7,323
Likes: 0
Received 2 Likes
on
2 Posts
Shortie shifter demonstration video.
91 NA, electric pump for aux ports & VDI, full dual exhaust, 225/50-15's on the back.
link to 2M video
91 NA, electric pump for aux ports & VDI, full dual exhaust, 225/50-15's on the back.
link to 2M video
Last edited by SureShot; 10-15-04 at 12:41 PM.
#13
Rotary Freak
i just got a t2 an d the guy i bought it from made one by cutting down the shifter and threaded a b&m shifter on it looked good but i switched it bavck to the stock until i get used to it
#14
Lets rock.
Join Date: Apr 2004
Location: SLC, Utah
Posts: 1,355
Likes: 0
Received 0 Likes
on
0 Posts
Odd. everyone asks me if I have a short shifter. I just used a S5 GTU **** and rod (huh huh) and put it into my TII tranny. There are some ***** where the thread is at the top of the **** itself. So it goes down alot. I'll show a pic of mine.
Thread
Thread Starter
Forum
Replies
Last Post
The1Sun
1st Generation Specific (1979-1985)
7
09-18-15 07:13 PM
REX7&Z32TT
New Member RX-7 Technical
2
09-14-15 08:46 AM