I tried searching for S4 lips but couldn't find any. Can anyone tell me what lips they have for the S4? Maybe side skirts and rear lips for the S4? I just god new TanabeGF springs and KYB AGX Shocks and really want to make my FC look nicer with a lip. So if anyone knows about any lips for S4's then shoot away. Thanks!

 

i like the look of just the s5 TII Lips and sideskirts.

 

rx7pro.com he has a nice lip for the s4. cheap too

 

180/240sx S13 lip and S5 sideskirts.

 

^ thats niooooce so any s13 lip will do the job i figure

 

Lip is ok, but that front mount sticking out like that is fugly.

 

Not much room behind the S4 bumper.
Does it really look that bad?

 

i bought a s14 bumper for the s5 - and it wont fit

might fit on the s4 just cause of the shape of the bumper

 

What? You bought an S14 bumper for your RX-7? Um, do you mean lip? I hope so.

If you do, then yes, that would be correct, they don't fit the S5. You see the S4 and S5 bumpers are different...

 

yeah, it's pretty bad.

 

it looks good to me..i'd rock it..its turbo; might be faster then the people talkin down on his car

 

I dig it!

 

Also i used a 90-92 mazda 626 sport lip. Not to much where you would rash it, but very tastefull looking too.

 

is there a lip for the s4 that looks like the (cork sport) Odura lip? i think that would look far more agressive. personaly if i had a s5 bumper skin and the Odura lip i would get rid of the grill and cut the bottom section in the middle out for a front mount intercooler which would give it almost like a "big mouth" look.

and example of the Odrua


and here is what the "big mouth" might look like

 

s14s are 4 inches wider than an FC. If you dont mind a little cutting and fiberglass work you can make it look good. zenki s14 lips look pretty good and shouldnt be too hard to find.

 

Does anyone have this lip? Or has anyone seen it on a car? How's the quality? Fitment? Etc...

 

Can the s5 front bumper fit on an s4?

 

im the only one that makes a decent lip that fits the car. My life is a total mess right now getting put together peice by peice. Financially I am a mess as well and I am not taking orders unless I have stock to ship whereas before I was taking prepayments but when things would go down it sometimes ended up being months before I could get things done which has been a major pain in the ***. I just shipped a prototype lip which was alright and hopefully the customer gets it installed an painted with no prob. I use much thicker gel coat now and a much better more flexible resin and layup than my first lip. Ill be putting out some good product with no wait hopefully in the future and when I can stand on my own two feet. Check me out www.rx7pro.com, and hopefully ill have stock notices on the website, i dont want to give anyone a headache or myself keeping a wait list.

 

shitty pic with rattle can paint. Hope to see one painted and on a car soon.

 

humm didnt realise the s14 was 4 inch wider - i reckon about 2 inch cut out the middle would do it

not sure yet - gonna wait till i fit the FMIC to see if i can make it fit

only cost me £10 ( $20 ) so it was worth a gamble

Stu / Grinder

 

s14 is about 2 inches wider than s13, s13 is about 2 inches wider than FC... sooo theoretically the s14 should be about 4 inches wider than the FC. But then again, most cars are a couple inches wider than an FC.

 

so any s13 lip? doesnt matter if its pignose ,zenki, or kouki