2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:

Rotor Housing

Thread Tools
 
Search this Thread
 
Old 08-05-03, 12:02 AM
  #1  
Junior Member

Thread Starter
 
rimarx@'s Avatar
 
Join Date: Nov 2001
Location: Santiago de Chile
Posts: 29
Likes: 0
Received 0 Likes on 0 Posts
Rotor Housing

That it differentiates they have the front and rear rotor housing in the RX7 Turbo II?
Sorry my english is very bad.
Old 08-05-03, 12:07 AM
  #2  
In Full Autist Cosplay

iTrader: (1)
 
Black13B's Avatar
 
Join Date: Nov 2002
Location: Alberta
Posts: 2,330
Likes: 0
Received 0 Likes on 0 Posts
Say what?

Housings are the same for both the front and back

The Turbo II housings are different from all the other housings available in the FC.
Old 08-05-03, 12:15 AM
  #3  
Junior Member

Thread Starter
 
rimarx@'s Avatar
 
Join Date: Nov 2001
Location: Santiago de Chile
Posts: 29
Likes: 0
Received 0 Likes on 0 Posts
they are possible to be used two rear housing in order to repair engine?

Last edited by rimarx@; 08-05-03 at 12:24 AM.
Old 08-05-03, 12:28 AM
  #4  
Open up! Search Warrant!

 
Project84's Avatar
 
Join Date: May 2002
Location: Kicking down doors in a neighborhood near you
Posts: 3,838
Likes: 0
Received 2 Likes on 2 Posts
yes.
Old 08-05-03, 12:37 AM
  #5  
Junior Member

Thread Starter
 
rimarx@'s Avatar
 
Join Date: Nov 2001
Location: Santiago de Chile
Posts: 29
Likes: 0
Received 0 Likes on 0 Posts
Thanks.
Old 08-05-03, 07:40 AM
  #6  
HAILERS

 
HAILERS's Avatar
 
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 21 Likes on 19 Posts
On a series four the rotor housings ARE NOT the same. But only for emissi
Old 08-05-03, 07:40 AM
  #7  
HAILERS

 
HAILERS's Avatar
 
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 21 Likes on 19 Posts
On a series four the rotor housings ARE NOT the same. But only for emissions purposes. If you are not concerned about emissions, you can swap with no problem. If you have to pass emissions you'll find the Port Air WILL NOT go to the exaust ports because the passage for the Port Air is now blocked because you/they have swapped the rotor housings.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
stickmantijuana
3rd Generation Specific (1993-2002)
13
01-09-18 11:19 AM
rotor_veux
2nd Generation Specific (1986-1992)
5
09-03-15 07:10 PM
ray green
1st Gen General Discussion
2
09-02-15 06:35 AM
VTECthis
3rd Generation Specific (1993-2002)
3
08-24-15 09:01 PM
cdn
2nd Generation Non-Technical and pictures
0
08-11-15 08:59 PM



Quick Reply: Rotor Housing



All times are GMT -5. The time now is 11:42 PM.