Aaron Cake

iTrader: (1)

That's brutal. Well, if you ever order rotors from me, you will be pleasently surprised that the rotors themselves are packed in plastic bags, and then Mono foam is used to secure them in the box. It's a bitch to unpack, but so far eccentrics, rotors, housings, etc. have NEVER been damged when I have shipped this way.

hypntyz7

No, I put those 9.7 rotors in like I told you.

At least yours was in a rotorhousing, which afforded it a degree of protection. The sides were scuffed a little, and one tip was bent just a hair, but nothing a little filing didnt take good care of.

I hate that ****, and will only do so under extreme circumstances. Such as 2 months ago when rpmcomputers (Richmond Abalos, New Orleans LA) sold me a core block and 2 rotors and rotorhousings and then disappeared...paypal found him at fault but couldnt collect any funds, so I'm in the ******* on that one too. Only then did I post a buyer beware thread in the feedback section, but not before he screwed 2-3 more people on teamfc3s.

Well, that's what its all about. Just like that last thread I put up about pineapple sleeve problems...I took a lot of **** for posting that, but it was information that needed to get out, which hadnt previously.

You'll have to ask rxse7en about that, he is the webpage maintenance man

Even most 7 owners have never closely examined or worked with a rotor, and they assume since theyre a heavy brick feeling chunk of metal, they must be really hard to damage. In truth because theyre totally hollow and all these seal grooves are cut out into them, they are very sensitive. Just sitting one down on a concrete floor can damage them.

Some of the n00b's on this board might disagree, but in person, yes, I prefer to be non-confrontational.


I really need to make a trip down to LA...there are 2 unsavory individuals who have done me VERY wrongly, and a face-to-face would be nice. Other than that, I usually let petty bullshit go, dont have time to worry with it.

Always. I like to find people that have 2+ so I can save on shipping, but Ill buy anything, even if it's just for a little bit of money. You get the satisfaction of knowing you're helping out a nice fellow such as myself, and helping to perpetuate the growth of the 7 community, by giving them to me very cheap

Okay there, "agent smith"...

The bad thing about buying cores is that you have no clue what you're actually buying. Sometimes you get one that is in mint condition, with all parts useable, sometimes you get one with the regular blown rotor and housing, and sometimes you get one that got overheated and abused, or was left to sit outside, and every part in it is rusted up and useless. Ones that are left to sit outside usually rust up ion 3 months' time. This makes the rotors, usually the irons, and sometimes even the rotorhousings useless.

Too bad there isnt a way I could buy them, open them up for inspection, and THEN pay based upon what is useful inside. As it stands, 1 out of 3 cores I get is pure junk, a waste of money, shipping, and time. BUt then sometimes you get a pleasant surprise...

No ****. HEre i send about 20-30 packages PER WEEK via UPS, probably $1000 per month worth. OF those, roughly 5-10% get broken in shipping. I'm not the best at packaging, and some odd things are hard to package like doorpanels, seats, transmissions, etc., but I do pretty well dependent on the item and destination. What REALLY pisses me off is when something gets damaged, and UPS wants to give me **** over the insurance claim. You'd think with all the damned money I give them, they would see that it is in their best interest to just approve my claim and go on, but no, they have to throw a wrench in the gears...


I always have a TON of bad rotors and rotorhousings on hand. I used to clean them, paint them, and make rotor clock/displays out of them which were cool as hell. Then some jackass bought one on ebay and came here complaining that it wasnt up to his standards for a $20 item, so I said **** it and quit putting my time into it. So now, I either give them away or throw them away. You can have some for $5 each plus cost of shipping. I just gave away about 15 to some guys who were here picking up an engine.

Mr. Gadget

Usually with those guys they are address skippers anyway. Keep the faith and keep up the good work!

But if you need a hand on a road trip . . . .

bl|nk

Did the stuff that I sent you go oke??

hypntyz7

Yes all that stuff made it fine, though the printer box was a bit worse for the wear

Just in time too...I just got a 91 t2 that needs a rebuild, and prior to this I had NO s5 t2 parts. So, at least I can get this thing on the road...the engine that was in it was severely overheated and allowed to sit and rust; all 3 irons had water jacket channels broken, both rotorhousings had broken exhaust studs, and both rotors were rusted solid, so there were no useable parts in that one. Glad I got this stuff. Hope we got yours straight, too. If not, I dunno what else to do.

bl|nk

sell the car and buy a mustang! err wait no way

Glad all went well.. yea that printer box had some weight in it. I'm just glad that rotor made it oke. I figured if it was in it's own box padded then inside another it should be oke.

Sorry i never got that dowel out of the front iron.. but to be honest my motivational factors were lacking so I was like it fits in the box.. it's good to go

Surprisingly the car seems to run better then it did before.. I haven't got alot of miles on it due to the temperature and my work schedule.. It seems to be a happier RX-7 just because it's being driven thanks agian for the help! btw R&L is sending me a check for 60 bills due to the screwed up pickup/delivery charges.

l33trx7

sweet .

Ok I would be interested in gettign some of the housings and rotors. It will only be a few the first time, however I might come back and get some more.

hypntyz7

Well, come and get 'em. I see youre in VA, not too far away.

l33trx7

heh, well its still a ways from TN however I might see what I can do.

fastrotaries

PM me on what you need, i have a spare car.

SonicRaT

iTrader: (6)

Well, whatcha usually pay for a blown rotor core? I'd be happy to get it out of my damn garage!

hypntyz7

youre the man holding it

i usually give $50-75 for s4 na blown cores. consider that i must pay at least $80 to ship it here, also.

SonicRaT

iTrader: (6)

Ok, I'll try to get a pallete and get it weighed/see how much shipping will be and such and if it's not too bad we'll make a deal or something. One less thing taking up space

SonicRaT

iTrader: (6)

Better yet, how about a deal for that TII hood that needs some TLC?

Core (front cover/oil pump/oil pan/rotors/housings/e-shaft) for the hood, and then we'll have to cover shipping for each? You know you want to get that ugly thing out of your sight, come on, you know you want to!

Mr. Gadget

This thread has kind of gotten off track. Is the solution only to use green loc-tite? to me it seems that we need to hear from others who have the sleeves in place and have had no issues using the green. Also, has anyone used other methods to attach the inserts?

The sleeves seem like a good mod. I just do not want to puke a rotor or risk it.

Has anyone used new sleeves with the inserts? is this a better option?

hypntyz7

This thread was not about PR sleeves. Search for posts by me in the last 3 months and youll find the original, lengthy PR sleeve thread.

This thread was about improperly shipped rotors.

Mr. Gadget

ooops my bad!

RotaryResurrection

iTrader: (8)

FWIW, importboi never gave me any kind of compensation for the fucked up rotors. Was doing a search for some old posts of mine and ran across this one, and remembered how much it sucks to have lost my money in this deal.

Still no job, huh importboi?

Aaron Cake

iTrader: (1)

This should be taken up in Good Guy/Bad Guy, not the 2nd gen tech section. Thread left open so others may comment, but this issue with importboi is not to be discussed here. Thanks.

Parastie

At least now i know why i have to save up some money, rip my core out, then eventually contact Kevin about a rebuild...should have the money by march or april, now if i can just convince my dad to rip the motor out while i'm away...

junior-coyote

Having shipped alot of stuff UPS, I can say that "insurance" mostly just covers a lost package. I once shipped a 1" swaybar (in a box) and it got bent. "Insurance" didn't cover it because it wasn't double boxed with 3" of padding in each box. They must have run over it with a truck to bend this thing.

iluvrx7z

I used to work for USPS, you'd be amazed the damage and careless handling that occurs. Please for your own sake everyone, package well

My .02

Dan