Profec B set 10PSI spikes to 13.6 and throttle sticcking problem
#1
Full Member
Thread Starter
Join Date: Mar 2006
Location: New York
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
Profec B set 10PSI spikes to 13.6 and throttle sticcking problem
I have a Profec B Spec II set at 10PSI and when i step on the throttle the car spikes out to 13.6PSI and the throttle sticks when i let go of it and revs up to 6K RPM then lets go. How can i fix both problems of the creep and throttle sticking... I have a 3" Racing beat exhaust and street port motor and a air intake.
Anyone got exact settings for the Profec B to set it steady at 10PSI i dont know if its my settings that are wrong
Anyone got exact settings for the Profec B to set it steady at 10PSI i dont know if its my settings that are wrong
#2
spending too much money..
iTrader: (2)
port your turbo wg as it is very small and this is a very common problem with turboed rx7's even more so with the 86-88 models. as far as your throttle sticking make sure your thottle linkage is well lubricated and make sure the throttle cable isn't binding up anywhere.
#5
Full Member
Thread Starter
Join Date: Mar 2006
Location: New York
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
nothing is ported whats the warmup system? where is it? on my throttle body i have a actuator that is controlled by a vacuum hose and it controlls the bottom flapper could that be the reason it stick so much? also im looking to get a Tubular manifold that will also work with some cheap ebay turbo meanwhile i want tog et the GT35R style turbo in about 2 months. Can someoen PM me a good tubular exhaust manifold to get currently or a setup? I have a 3 bolt downpipe but i dotn know where i can buy a V Band Adapter to it
#7
Boost in..Apex seals out.
Join Date: Nov 2003
Location: Maryland, 21794
Posts: 1,931
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 87RX7TurboII
nothing is ported whats the warmup system? where is it? on my throttle body i have a actuator that is controlled by a vacuum hose and it controlls the bottom flapper could that be the reason it stick so much? also im looking to get a Tubular manifold that will also work with some cheap ebay turbo meanwhile i want tog et the GT35R style turbo in about 2 months. Can someoen PM me a good tubular exhaust manifold to get currently or a setup? I have a 3 bolt downpipe but i dotn know where i can buy a V Band Adapter to it
If you don't even know how to control boost..why would you get a bigger turbo? Boost controllers can only RAISE boost, you're wastegate is the only factor in LOWERING it.
The accelerated warmup system..crack open an FSM/WSM. It's a bit of thermowax on the rear of the throttle body, it limits you from going wide open throttle while the car is cold.
You're throttle body flaps are not controlled via vacuum, you need to take a closer look. Once again, try cracking open an FSM/WSM. Or remove the TB and play with it....
Lube you're pedal assembly, and make sure you're carpet isn't what is catching the pedal. Mine was
Trending Topics
#8
Alcohol Fueled!
iTrader: (2)
Originally Posted by 87RX7TurboII
I have a Profec B Spec II set at 10PSI and when i step on the throttle the car spikes out to 13.6PSI and the throttle sticks when i let go of it and revs up to 6K RPM then lets go. How can i fix both problems of the creep and throttle sticking... I have a 3" Racing beat exhaust and street port motor and a air intake.
Anyone got exact settings for the Profec B to set it steady at 10PSI i dont know if its my settings that are wrong
Anyone got exact settings for the Profec B to set it steady at 10PSI i dont know if its my settings that are wrong
Read the manual.. If your boost is spiking then you need to lower your "start Boost" setting. If its creeping, then you need to adjust your "Duty cycle" setting.
Rat
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
CaptainKRM
2nd Generation Specific (1986-1992)
14
08-26-15 09:52 PM