Snoopy240

iTrader: (19)

Ive searched and searched and searched! and nothing was found!!
I need a pivot controller wiring diagram.. I have 4 wires and no clue where they all go


--Thanks

87 t-66

iTrader: (133)

solareon

iTrader: (1)

from a google search i am guessing you are trying to do a sleepy eyes setup on your rx7

just use the manual turn up on the lights and then pull the retractor fuse in the engine bay then use the adjustment ***** under the headlights to lower them where you want.

Snoopy240

iTrader: (19)

im not TRYING to do sleepy eyes... I picked up a Pivot controller out the junkyard for FREE! so its going in the 7... simple as that.. blame me?
Picked up a safc for FREE, so its going in my car... blame me?!

k then! lol

Ive google'd EVERYTHING pivot, i cant find a wiring diagram to save my life

cloudzero

iTrader: (1)

Hmm i think the big problem is, pivot makes more than one controller. People need to know what you have besides a pivot controller.
Pivot speed meter controller
Pivot throttle controller
Pivot water spray controller
Pivot shift lamp controller
Pivot voltage controller
Pivot racing monitor controller
Pivot headlamp controller
Tell us what we need to know, and we might be able to help you

Snoopy240

iTrader: (19)

Pivot RHU-M headlight controller

Snoopy240

iTrader: (19)

no1 knows anything?

jake1191

iTrader: (1)

look in the FSM and then look at this http://www.zeroyon.com/pics/installs...tructions.html then you can subsitute the wire types for the correct one vs. the 240sx wire.


OR


Look in the fsm and see what wires do what on the headlight setup and DONT cut them but stick the wires in the end of the plug to make contact until you find which wires work. Still you will need to use a few bits of info from the above link.

Howru

iTrader: (25)

I have a PDF of the installation instructions I found a few years ago. They're too large to attach here (1.1MB) but I've pulled the pages needed for FC's.

HAI-TEK7

iTrader: (31)

heres a link for the pdf^^^ pg 6

http://www.3sxperformance.com/instal...ish-pivrhu.pdf

solareon

iTrader: (1)

Not to be a jerk or nothing but from all the above posts the piece you got from the junkyard is for controlling the flip up headlights aka sleepy eyes. Not hating but it seems like an awful lot of work to cut and splice wires when you could just turn the screw and pull the fuse.

Snoopy240

iTrader: (19)

Well first off, it was FREE.
2nd off, little bit of cutting and wiring just adds to the list of wiring im already doing to the car... no biggie

dawicka2

It took me 20 minutes to wire the pivot controller.

The pivot controller enables you to drive safely at night, while retaining the low profile look during the day.

Plus pulling the fuse and turning the **** every time is so much more "work".

Night time visability is your friend.

john ny

Gene

iTrader: (1)

I found a free dog poop on the sidewalk in front of my house, but I'm not putting it in the car just because it was free.

The "low profile" look during the day is the headlights fully closed, like they should be. Sleepy eye headlights look dumbtarded, and increase drag and most likely lift as well.

Snoopy240

iTrader: (19)

Well if you were considering putting dog poop in your car youve got issues..

As for lift/drag, im not going for "speed". Im going for how I want the car to look, and what I want to buy and install. Im not building a 8sec 13b drag car, im building a slow stock motor, intake/exhaust, slammed, full suspension, CLEAN car.

Pics will be posted later.

As for the flaming, keep your opinions to yourself, I dont go running my mouth on how stock someones car is or how build and riced out is it. So dont do it to me.