N/A to TII swap...I need a Guru!!!
06-29-06, 03:14 PM
#26
Banned. I got OWNED!!!
Originally Posted by HAILERS
That first picture is a condenser for the oil pressure sensor. The oil pressure sensor wire has a wire that is spliced to it and has a connector that mates with that condenser. Ther is another condenser just like it under the trai coil assy and that one is connected to the supply voltage wire to the coils.
That is NOT the ground for the ECU that is located under the intake, on top of the rear ROTOR HOUSING. That ground has a ring ternimal and has two wires in the ternimal. Both black.
That is NOT the ground for the ECU that is located under the intake, on top of the rear ROTOR HOUSING. That ground has a ring ternimal and has two wires in the ternimal. Both black.
07-24-06, 06:11 PM
#27
Registered Craft User
Thread Starter
Join Date: Jan 2006
Location: Texas
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
My Turbovert (Swordfish) is complete. Everything is in. Ready to race .......with only one issue.....It won't idle, unless I set the idle above 2000 rpm (it just dies at lower rpms). There is a strange hissing noise coming from around the trottle & dynamic chamber. I suspect a vacuum leak, but I'm not finding anything. Any thoughts or suggestions?
07-25-06, 12:18 PM
#29
Registered Craft User
Thread Starter
Join Date: Jan 2006
Location: Texas
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
I found the leak!! One of the primary fuel injectors has a warped seal and a cracked tip......so anyone in the Austin area have 1 or 2, 550cc 89-91 TII fuel injectors they'd be willing to part with?
07-26-06, 06:11 PM
#30
Registered Craft User
Thread Starter
Join Date: Jan 2006
Location: Texas
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
Alright. The vacuum leak has been fixed and the car now idles as it should!!
.....However, one previously unseen problem has now arisen.......When I move the steering wheel, the rpm's drop. Power Steering fluid is just as it should be (Silent and smooth as buttah). What's up wit that?
.....However, one previously unseen problem has now arisen.......When I move the steering wheel, the rpm's drop. Power Steering fluid is just as it should be (Silent and smooth as buttah). What's up wit that?
07-26-06, 06:49 PM
#31
Registered Craft User
Thread Starter
Join Date: Jan 2006
Location: Texas
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
.....other than that small quirk.....
Here's The Finished Product!!!
So what do you think?
[Notice the huge gaping hole left from the lack of a battery (It's in the trunk).....I have an air horn from a 18-Wheeler (Semi-Truck) that will perfectly fill that spot!!^_^ hehe!]
Here's The Finished Product!!!
So what do you think?
[Notice the huge gaping hole left from the lack of a battery (It's in the trunk).....I have an air horn from a 18-Wheeler (Semi-Truck) that will perfectly fill that spot!!^_^ hehe!]
08-09-06, 06:25 AM
#33
The Cause of Death
Originally Posted by 12RotorMonster
Alright. The vacuum leak has been fixed and the car now idles as it should!!
.....However, one previously unseen problem has now arisen.......When I move the steering wheel, the rpm's drop. Power Steering fluid is just as it should be (Silent and smooth as buttah). What's up wit that?
.....However, one previously unseen problem has now arisen.......When I move the steering wheel, the rpm's drop. Power Steering fluid is just as it should be (Silent and smooth as buttah). What's up wit that?
Does it stall? If it doesn't stall, don't worry about it.
It's like putting the AC on, the idle will probably drop for a few seconds, then slowly rise back up.
James
08-09-06, 07:59 AM
#35
Registered Craft User
Thread Starter
Join Date: Jan 2006
Location: Texas
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by chaosseven
Where in Texas are you located?
I think MY turbovert can beat your turboverts ***!
Just sayin.
I think MY turbovert can beat your turboverts ***!
Just sayin.
08-09-06, 08:02 AM
#36
Registered Craft User
Thread Starter
Join Date: Jan 2006
Location: Texas
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by spot_skater
BAC valve.
Does it stall? If it doesn't stall, don't worry about it.
It's like putting the AC on, the idle will probably drop for a few seconds, then slowly rise back up.
James
Does it stall? If it doesn't stall, don't worry about it.
It's like putting the AC on, the idle will probably drop for a few seconds, then slowly rise back up.
James
Awesome THX!!!
12-08-07, 01:57 PM
#37
Al's2ndgenFC
Join Date: Dec 2007
Location: Miami Florida
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
hi i have a question
hey hows it going im new to the mazda game i had a srt4 before but i crashed it at 155 miles an ahour but that a long story......... my plans are to do the same as you intsall the 91fc13bturbo motot into a 91 fc convert.. i was wondering if you can give me some pointers on doing this i would be really greatfull if you can ......... thanks if you can help and my names alberto
Thread
Thread Starter
Forum
Replies
Last Post
