N/A to TII swap...I need a Guru!!!
Banned. I got OWNED!!!
Joined: Aug 2004
Posts: 8,789
Likes: 2
From: Jacksonville, NC
Originally Posted by HAILERS
That first picture is a condenser for the oil pressure sensor. The oil pressure sensor wire has a wire that is spliced to it and has a connector that mates with that condenser. Ther is another condenser just like it under the trai coil assy and that one is connected to the supply voltage wire to the coils.
That is NOT the ground for the ECU that is located under the intake, on top of the rear ROTOR HOUSING. That ground has a ring ternimal and has two wires in the ternimal. Both black.
That is NOT the ground for the ECU that is located under the intake, on top of the rear ROTOR HOUSING. That ground has a ring ternimal and has two wires in the ternimal. Both black.
Thread Starter
Registered Craft User
Joined: Jan 2006
Posts: 98
Likes: 0
From: Texas
My Turbovert (Swordfish) is complete. Everything is in. Ready to race .......with only one issue.....It won't idle, unless I set the idle above 2000 rpm (it just dies at lower rpms). There is a strange hissing noise coming from around the trottle & dynamic chamber. I suspect a vacuum leak, but I'm not finding anything. Any thoughts or suggestions?
most likely a vac leak, you could spray some crap down on it and see if it sucks it in to verify if its a leak or not....but I can garuntee you it is.
Pull the manifolds and go to autozone and stock up on vac line.
Pull the manifolds and go to autozone and stock up on vac line.
Thread Starter
Registered Craft User
Joined: Jan 2006
Posts: 98
Likes: 0
From: Texas
I found the leak!! One of the primary fuel injectors has a warped seal and a cracked tip......so anyone in the Austin area have 1 or 2, 550cc 89-91 TII fuel injectors they'd be willing to part with?
Thread Starter
Registered Craft User
Joined: Jan 2006
Posts: 98
Likes: 0
From: Texas
Alright. The vacuum leak has been fixed and the car now idles as it should!!
.....However, one previously unseen problem has now arisen.......When I move the steering wheel, the rpm's drop. Power Steering fluid is just as it should be (Silent and smooth as buttah). What's up wit that?
.....However, one previously unseen problem has now arisen.......When I move the steering wheel, the rpm's drop. Power Steering fluid is just as it should be (Silent and smooth as buttah). What's up wit that?
Thread Starter
Registered Craft User
Joined: Jan 2006
Posts: 98
Likes: 0
From: Texas
.....other than that small quirk.....
Here's The Finished Product!!!
So what do you think?
[Notice the huge gaping hole left from the lack of a battery (It's in the trunk).....I have an air horn from a 18-Wheeler (Semi-Truck) that will perfectly fill that spot!!^_^ hehe!]
Here's The Finished Product!!!
So what do you think?
[Notice the huge gaping hole left from the lack of a battery (It's in the trunk).....I have an air horn from a 18-Wheeler (Semi-Truck) that will perfectly fill that spot!!^_^ hehe!]
The Cause of Death
Joined: Mar 2004
Posts: 2,202
Likes: 2
From: New York
Originally Posted by 12RotorMonster
Alright. The vacuum leak has been fixed and the car now idles as it should!!
.....However, one previously unseen problem has now arisen.......When I move the steering wheel, the rpm's drop. Power Steering fluid is just as it should be (Silent and smooth as buttah). What's up wit that?
.....However, one previously unseen problem has now arisen.......When I move the steering wheel, the rpm's drop. Power Steering fluid is just as it should be (Silent and smooth as buttah). What's up wit that?
Does it stall? If it doesn't stall, don't worry about it.
It's like putting the AC on, the idle will probably drop for a few seconds, then slowly rise back up.
James
Originally Posted by 12RotorMonster
[Notice the huge gaping hole left from the lack of a battery (It's in the trunk).....I have an air horn from a 18-Wheeler (Semi-Truck) that will perfectly fill that spot!!^_^ hehe!]
Thread Starter
Registered Craft User
Joined: Jan 2006
Posts: 98
Likes: 0
From: Texas
Originally Posted by spot_skater
BAC valve.
Does it stall? If it doesn't stall, don't worry about it.
It's like putting the AC on, the idle will probably drop for a few seconds, then slowly rise back up.
James
Does it stall? If it doesn't stall, don't worry about it.
It's like putting the AC on, the idle will probably drop for a few seconds, then slowly rise back up.
James
Awesome THX!!!
Al's2ndgenFC
Joined: Dec 2007
Posts: 5
Likes: 0
From: Miami Florida
hi i have a question
hey hows it going im new to the mazda game i had a srt4 before but i crashed it at 155 miles an ahour but that a long story......... my plans are to do the same as you intsall the 91fc13bturbo motot into a 91 fc convert.. i was wondering if you can give me some pointers on doing this i would be really greatfull if you can ......... thanks if you can help and my names alberto
Thread
Thread Starter
Forum
Replies
Last Post
MidnightOwl
2nd Generation Specific (1986-1992)
1
Sep 25, 2015 10:24 PM
