interest in Solid Diff-subframe mount??
#1
Brappidy Brap
Thread Starter
iTrader: (5)
Join Date: Mar 2007
Location: South Jersey
Posts: 504
Likes: 0
Received 0 Likes
on
0 Posts
interest in Solid Diff-subframe mount??
This happened after about 1100 miles and im getting pissed off because its the 2nd one.
What i am asking in this thread is, Would anyone be interested in a solid steel mount instead of the POS rubber mount??
I am asking because im getting this done in april and i could get a whole bunch done while im there. Im sure the price would be very minimal and it is a permanent fix to an annoying *** problem.
What i am asking in this thread is, Would anyone be interested in a solid steel mount instead of the POS rubber mount??
I am asking because im getting this done in april and i could get a whole bunch done while im there. Im sure the price would be very minimal and it is a permanent fix to an annoying *** problem.
#3
Refined Valley Dude
Join Date: Oct 2001
Location: Kitchener, Ontario (Hamilton's armpit)
Posts: 2,283
Likes: 0
Received 2 Likes
on
2 Posts
That happened two 7s ago when I put a racing clutch in. You could save yourself money and hassle and just put in a pinion snubber.
https://www.rx7club.com/2nd-generation-specific-1986-1992-17/finally-changed-out-front-diff-mount-164843/
Cost me $15 for two of them. Drilled 1 hole and slapped it in. No fabrication and no more broken diff mounts.
https://www.rx7club.com/2nd-generation-specific-1986-1992-17/finally-changed-out-front-diff-mount-164843/
Cost me $15 for two of them. Drilled 1 hole and slapped it in. No fabrication and no more broken diff mounts.
#5
not a drifter
iTrader: (133)
That happened two 7s ago when I put a racing clutch in. You could save yourself money and hassle and just put in a pinion snubber.
https://www.rx7club.com/showthread.php?t=164843
Cost me $15 for two of them. Drilled 1 hole and slapped it in. No fabrication and no more broken diff mounts.
https://www.rx7club.com/showthread.php?t=164843
Cost me $15 for two of them. Drilled 1 hole and slapped it in. No fabrication and no more broken diff mounts.
#6
Brappidy Brap
Thread Starter
iTrader: (5)
Join Date: Mar 2007
Location: South Jersey
Posts: 504
Likes: 0
Received 0 Likes
on
0 Posts
actually now that i read it, i still need to have the stock mount. I want to get rid of it and replace the mount completely while having the stiffest mounting possible.
#7
87 SE WITH S5 T2 SWAP
iTrader: (11)
need to be careful with a solid or welded mount,the mount needs the rubber because the diff and shaft move up and down a little during load,with the rubber in place the pieces move in a independent way,if the shaft wants to move down and the diff up it happens thanks to the rubber,now if the mount is welded shut you have no play at all meaning that all pieces are gonna try to move at in the same direction putting more stress and load on the shaft and on the front rear end bearing causing it to fail,it did happened to me twice.
Trending Topics
#9
87 SE WITH S5 T2 SWAP
iTrader: (11)
not that much stress thanks to the rubber,the rubber acts like a dampener it takes most of the loads and vibration,i fixed my problem replacing the mount with the stiffer version,replacing the 2 round bushing that hold the rear end casing in place,stiffer tranny mount and a nice suspension setup.
#10
Brappidy Brap
Thread Starter
iTrader: (5)
Join Date: Mar 2007
Location: South Jersey
Posts: 504
Likes: 0
Received 0 Likes
on
0 Posts
Your the perfect person to ask then.
I just installed the MMR solid subframe, diff, trans and motor bushings. Should i still use that diff mount or can i get away using just a snubber without the mount?
I just installed the MMR solid subframe, diff, trans and motor bushings. Should i still use that diff mount or can i get away using just a snubber without the mount?
#13
Brappidy Brap
Thread Starter
iTrader: (5)
Join Date: Mar 2007
Location: South Jersey
Posts: 504
Likes: 0
Received 0 Likes
on
0 Posts
dammit! y do u guys have to rain on my parade. What u are saying is really making sense so i guess i have to buy another ******* mount. So be it, if i do it right now i wont have a prob in the future
#14
Fistful of steel
iTrader: (7)
You can run a soild front mount ONLY if you run solid diff and subframe mounts as well.
The reason people break the tab off the subframe is because they do not have all the other mounts soild. The deflection from the softer subframe and rear diff bushings stress the solid front diff mount and the tab on the subframe eventually breaks off.
If everything is soild, nothing moves and you have nothing to worry about. You already have all the other MMR soild mounts, you are good to go.
I bought a good used OEM mount for a few bucks from another forum member and welded it up. It has worked great.
The reason people break the tab off the subframe is because they do not have all the other mounts soild. The deflection from the softer subframe and rear diff bushings stress the solid front diff mount and the tab on the subframe eventually breaks off.
If everything is soild, nothing moves and you have nothing to worry about. You already have all the other MMR soild mounts, you are good to go.
I bought a good used OEM mount for a few bucks from another forum member and welded it up. It has worked great.