2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.

fuel pump rewire quick question

Thread Tools
 
Search this Thread
 
Old Sep 26, 2003 | 07:35 PM
  #1  
minclo's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Mar 2002
Posts: 142
Likes: 0
From: Irving, Tx
fuel pump rewire quick question

How the hell do i get power wire from the battery through to the rear shock tower? I don't see a way through the fire wall and i don't wanna tear the fire wall up. Do i just go under the car or what??
Reply
Old Sep 26, 2003 | 07:45 PM
  #2  
Senior Member
Tenured Member 05 Years
 
Joined: Dec 2002
Posts: 286
Likes: 0
From: Racing Bear's Tepee
Refer to NZconvertible's diagram about middle ways of page:
>https://www.rx7club.com/forum/showth...=NZConvertible
Reply
Old Sep 26, 2003 | 07:49 PM
  #3  
minclo's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Mar 2002
Posts: 142
Likes: 0
From: Irving, Tx
i have both the S4 and S5 version of that saved...but that diagram doesn't tell me how to get the power wire from the battery to the back of the car...i would rather not have a wire coming out of my engine bay then back in through my driver side window...
Reply
Old Sep 26, 2003 | 07:50 PM
  #4  
Scott 89t2's Avatar
SOLD THE RX-7!
Tenured Member 10 Years
 
Joined: Mar 2001
Posts: 7,451
Likes: 0
From: Vancouver, BC, Canada
there are a few holes in the firewall. where the speedo cable goes though is the biggest. near the oil filer.
Reply
Old Sep 26, 2003 | 07:52 PM
  #5  
1SxyRXy's Avatar
my fc broke
Tenured Member 20 Years
 
Joined: Feb 2003
Posts: 2,231
Likes: 0
From: rohnert park,CA/ bay area
i just did mine the other day. its not hard at all
Reply
Old Sep 26, 2003 | 08:01 PM
  #6  
Senior Member
Tenured Member 05 Years
 
Joined: Dec 2002
Posts: 286
Likes: 0
From: Racing Bear's Tepee
Yes but a careful look would lead to an answer :-)
Reply
Old Sep 26, 2003 | 08:02 PM
  #7  
minclo's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Mar 2002
Posts: 142
Likes: 0
From: Irving, Tx
how do i get the lil cap off that's covering the hole? can i just pry it off with a screwdriver? i don't wanna do anything that might break something...
Reply
Old Sep 26, 2003 | 08:06 PM
  #8  
minclo's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Mar 2002
Posts: 142
Likes: 0
From: Irving, Tx
Originally posted by RunningDeer
Yes but a careful look would lead to an answer :-)
I think i just popped a vessel in my eye looking... mind just telling me how??
Reply
Old Sep 26, 2003 | 08:15 PM
  #9  
1SxyRXy's Avatar
my fc broke
Tenured Member 20 Years
 
Joined: Feb 2003
Posts: 2,231
Likes: 0
From: rohnert park,CA/ bay area
to get through the hole i went through the inside of the car and pished it through with a screw driver and then pulled it through from the engine bay
Reply
Old Sep 26, 2003 | 08:33 PM
  #10  
Senior Member
Tenured Member 05 Years
 
Joined: Dec 2002
Posts: 286
Likes: 0
From: Racing Bear's Tepee
look at below, stroll down a bit to the RED writing, where it states " went up passenger fender... >http://1300cc.com/howto/how2/rewire.htm

Good Luck :-)
Reply
Old Sep 26, 2003 | 08:40 PM
  #11  
Scott 89t2's Avatar
SOLD THE RX-7!
Tenured Member 10 Years
 
Joined: Mar 2001
Posts: 7,451
Likes: 0
From: Vancouver, BC, Canada
umm that doesn't get him through the firewall
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
Jul 1, 2023 04:40 PM
Rotospectre
New Member RX-7 Technical
3
Mar 28, 2018 03:33 PM
alphawolff
1st Generation Specific (1979-1985)
17
Nov 17, 2015 05:57 PM




All times are GMT -5. The time now is 03:33 PM.