fc lim >adapter>fd uim bolt length urgent
#2
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
Sorry ..Trick question.
How think is the Spacer?
How I Measured was to throw a piece of Threaded Metric rod through the holes and screw it in..grab that piece and mark it with the measurement(tape it.use a marker,whatever) and get the bolt required.
How think is the Spacer?
How I Measured was to throw a piece of Threaded Metric rod through the holes and screw it in..grab that piece and mark it with the measurement(tape it.use a marker,whatever) and get the bolt required.
#3
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
The thread is the same on all the upper manifold bolts.so if you need to just grab a nut from one of the lower manifold studs...
Oh ya,you will need those Studs extended TOO..so they can hold everything together.
Oh ya,you will need those Studs extended TOO..so they can hold everything together.
#5
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
it is over 4 inches long..
LOOK at the old bolt that was in there..add the spacer thickness and you get an idea.
I thought 110mm X .8metric...that is ROUGHLY
LOOK at the old bolt that was in there..add the spacer thickness and you get an idea.
I thought 110mm X .8metric...that is ROUGHLY
#7
Yo misty your the man 110 m8 x 1.25 my threads were dirty so I had to clean them with a tap. So now I gatta get the 5 other bolts... I might start the car today if I can do everything befor it gets late.
I accidently got trans line instead of fuel line I hope it holds enough to start the car and. I hope that my fuel pump wornt turn on cause I didn't connect some wire or something
I accidently got trans line instead of fuel line I hope it holds enough to start the car and. I hope that my fuel pump wornt turn on cause I didn't connect some wire or something
Trending Topics
#8
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
That line needs to hold 40-50 PSI so it better be rated as such or it will burst.(<<<WARNING!)
HI pressure fuel line(the rubber stuff) is a little expensive but it works and holds the pressure of the Fuel system fine.
HI pressure fuel line(the rubber stuff) is a little expensive but it works and holds the pressure of the Fuel system fine.
#9
i think its says reinforced trans cooler line i forget but i confused it because A it was labled wrong and B it have the strands of string in it.. ill just get some fuel line later this week.
sooo as of right now i just have to figure out the wiring and i should be able to start her up
sooo as of right now i just have to figure out the wiring and i should be able to start her up
Thread
Thread Starter
Forum
Replies
Last Post
toplessFC3Sman
2nd Generation Specific (1986-1992)
6
03-20-18 01:54 PM
Adaptronic 1280s Hot Start 3 Rotor 20b RX7
Monsterbox
Adaptronic Engine Mgmt - AUS
5
09-11-15 03:29 PM