fc lim >adapter>fd uim bolt length urgent
Thread Starter
Joined: Feb 2009
Posts: 441
Likes: 0
From: https://t.me/pump_upp
fc lim >adapter>fd uim bolt length urgent
does any one know the bolt length im in the store far from my garage
and i dont kno the length or the pitch
can some one please tell me asap
and i dont kno the length or the pitch
can some one please tell me asap
Joined: Sep 2005
Posts: 25,581
Likes: 136
From: Smiths Falls.(near Ottawa!.Mapquest IT!)
Sorry ..Trick question.
How think is the Spacer?
How I Measured was to throw a piece of Threaded Metric rod through the holes and screw it in..grab that piece and mark it with the measurement(tape it.use a marker,whatever) and get the bolt required.
How think is the Spacer?
How I Measured was to throw a piece of Threaded Metric rod through the holes and screw it in..grab that piece and mark it with the measurement(tape it.use a marker,whatever) and get the bolt required.
Joined: Sep 2005
Posts: 25,581
Likes: 136
From: Smiths Falls.(near Ottawa!.Mapquest IT!)
The thread is the same on all the upper manifold bolts.so if you need to just grab a nut from one of the lower manifold studs...
Oh ya,you will need those Studs extended TOO..so they can hold everything together.
Oh ya,you will need those Studs extended TOO..so they can hold everything together.
Thread Starter
Joined: Feb 2009
Posts: 441
Likes: 0
From: https://t.me/pump_upp
damn... i guess ill have to go to the garage and measure.. or ill just buy 2 or 3 inch bolts and wish for the best.. aw crap i still gata figure out the thread pitch.. to the garge i go .. thanks misty
Joined: Sep 2005
Posts: 25,581
Likes: 136
From: Smiths Falls.(near Ottawa!.Mapquest IT!)
it is over 4 inches long..
LOOK at the old bolt that was in there..add the spacer thickness and you get an idea.
I thought 110mm X .8metric...that is ROUGHLY
LOOK at the old bolt that was in there..add the spacer thickness and you get an idea.
I thought 110mm X .8metric...that is ROUGHLY
Thread Starter
Joined: Feb 2009
Posts: 441
Likes: 0
From: https://t.me/pump_upp
i just got the manifold with out bolts or anything so i honestly dont kno.. ill just get the bolts some other time if worst comes to worst i cant make it back in time
Thread Starter
Joined: Feb 2009
Posts: 441
Likes: 0
From: https://t.me/pump_upp
Yo misty your the man 110 m8 x 1.25 my threads were dirty so I had to clean them with a tap. So now I gatta get the 5 other bolts... I might start the car today if I can do everything befor it gets late.
I accidently got trans line instead of fuel line I hope it holds enough to start the car and. I hope that my fuel pump wornt turn on cause I didn't connect some wire or something
I accidently got trans line instead of fuel line I hope it holds enough to start the car and. I hope that my fuel pump wornt turn on cause I didn't connect some wire or something
Trending Topics
Joined: Sep 2005
Posts: 25,581
Likes: 136
From: Smiths Falls.(near Ottawa!.Mapquest IT!)
That line needs to hold 40-50 PSI so it better be rated as such or it will burst.(<<<WARNING!)
HI pressure fuel line(the rubber stuff) is a little expensive but it works and holds the pressure of the Fuel system fine.
HI pressure fuel line(the rubber stuff) is a little expensive but it works and holds the pressure of the Fuel system fine.
Thread Starter
Joined: Feb 2009
Posts: 441
Likes: 0
From: https://t.me/pump_upp
i think its says reinforced trans cooler line i forget but i confused it because A it was labled wrong and B it have the strands of string in it.. ill just get some fuel line later this week.
sooo as of right now i just have to figure out the wiring and i should be able to start her up
sooo as of right now i just have to figure out the wiring and i should be able to start her up
Thread
Thread Starter
Forum
Replies
Last Post
toplessFC3Sman
2nd Generation Specific (1986-1992)
6
Mar 20, 2018 01:54 PM
Adaptronic 1280s Hot Start 3 Rotor 20b RX7
Monsterbox
Adaptronic Engine Mgmt - AUS
5
Sep 11, 2015 03:29 PM
