Blinker doesn't work
#1
Junior Member
Thread Starter
Join Date: Jul 2005
Location: Irvine, CA
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Blinker doesn't work
Okay guys, I've searched, and can't find the answer.
Here's my problem:
My left turn signal works fine, but my right doesn't. When I turn on my right turn signal, it clicks fast, but the light doesn't go on in the guage cluster, the front signal, or the rear signal. Also, when I turn on my hazards, only the left side blinks. Again, the whole right side is disabled. What is the problem, can I fix it, and how?!?
Here's my problem:
My left turn signal works fine, but my right doesn't. When I turn on my right turn signal, it clicks fast, but the light doesn't go on in the guage cluster, the front signal, or the rear signal. Also, when I turn on my hazards, only the left side blinks. Again, the whole right side is disabled. What is the problem, can I fix it, and how?!?
#2
Former Moderator. RIP Icemark.
Sounds like a bad CPU flasher board. You can try resoldering it yourself or I have already rebuilt ones available on my webstore/site.
You may wish to revise your search, as this is a somewhat common problem and covered already once this week.
You may wish to revise your search, as this is a somewhat common problem and covered already once this week.
#4
Former Moderator. RIP Icemark.
Originally Posted by Karack
maybe check the bulbs first..
I suppose it is possible however that both turn signal bulbs were burnt out on the same side, which would lead to the same problem.
#7
Full Member
Join Date: Mar 2005
Location: Fort walton beach FL
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
Usually when your blinker blinks fast, it means that either a taillight or a headlight is out, Chekc your taillights, brakelights, and backuplights on the right side. and also side markers....... but i dont think second gens have them...
Trending Topics
#8
Junior Member
Thread Starter
Join Date: Jul 2005
Location: Irvine, CA
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Well, as far as I know, all the bulbs work. I've checked them already. I'm thinking it's blinking fast because it was grounded out or something. I know it can't be the bulbs because the green arrow in the guage cluster doesn't light up either.
The only thing that doesn't work on the right tail light are the turn signals. Everything else works fine.
Icemark, I'll try revising my search.
Thanks for the input everyone, it is much appreciated!!
The only thing that doesn't work on the right tail light are the turn signals. Everything else works fine.
Icemark, I'll try revising my search.
Thanks for the input everyone, it is much appreciated!!
#9
Junior Member
Thread Starter
Join Date: Jul 2005
Location: Irvine, CA
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Okay Icemark, after revising my search, I've come to the conclusion that you are right. I think I'm going to need that $40 CPU Flasher Board of yours. I'm sending over a pm!
#11
Former Moderator. RIP Icemark.
Originally Posted by nopistons13
either check your ground or the place where the power source divides in the circut. you may have a bad connection somewhere.
Please do not post if you do not know! Posting inaccurate information is a bannable offense here.
Thread
Thread Starter
Forum
Replies
Last Post
streetlegal?
New Member RX-7 Technical
13
03-17-22 02:46 PM
thecody59
1st Generation Specific (1979-1985)
40
08-23-15 06:41 PM
smikels
2nd Generation Specific (1986-1992)
3
08-18-15 01:26 PM