blew my first motor
#78
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
Was told the goopy seals woundt be a good street seal. Might just stick with the RA stuff for this build and see How it works out. I'll talk to them about when I get my housings refinished but I would like to replace this N/A housing with a tII then shoot them down there also need to find a local place to lap my irons. I Wana get a set of Ito porting templates
#81
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
rotor tips are good idk I can feel a decent line with my figuretip on the side I want to get them lapped im gonna bring every thing to judge ito to look over gonna buy some of his porting plates but yeah its gonna basically be everything new or resurfaced
#82
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
So I did a ruff degreasing on everything, then packed it up to meet the Judge himself at his new shop Advanced Rotary Performance hes just moving in, but hes back and like 20 minutes from me in Paterson.
I contacted him the other day about some porting templates and housings Id like to purchase.
He replied quickly and gave me his number and new shops address.
We met up at the new shop hes renovating and he is very nice, I was there for over an hour talking rotary and hes very knowledgeable.
He inspected all my plates and housings for me.
Told me not to spend my money lapping the housings on my first build, that mine are in reuseable condition. God forbid some thing happened I wouldnt wana waste all that money. He said I should get more expeirience and confidence before spending the big bux on everything, I feel hes right. He said the ports are mild and could just use some minor touch up im gonna purchase some of his larger templates and purchase a pineapple exhuast template.
The housings are ok, Im gonna replace the rear one with one of Itos and keep the front even tho it has some very minor flaking in the compression area they both will be brought to John at Goopy for resurfacing.
Cant wait to start this build. Looking for alittle over 400whp. Ito sid thats fine for these irons anything more Id have to upgrade.
For now,
James
I contacted him the other day about some porting templates and housings Id like to purchase.
He replied quickly and gave me his number and new shops address.
We met up at the new shop hes renovating and he is very nice, I was there for over an hour talking rotary and hes very knowledgeable.
He inspected all my plates and housings for me.
Told me not to spend my money lapping the housings on my first build, that mine are in reuseable condition. God forbid some thing happened I wouldnt wana waste all that money. He said I should get more expeirience and confidence before spending the big bux on everything, I feel hes right. He said the ports are mild and could just use some minor touch up im gonna purchase some of his larger templates and purchase a pineapple exhuast template.
The housings are ok, Im gonna replace the rear one with one of Itos and keep the front even tho it has some very minor flaking in the compression area they both will be brought to John at Goopy for resurfacing.
Cant wait to start this build. Looking for alittle over 400whp. Ito sid thats fine for these irons anything more Id have to upgrade.
For now,
James
#84
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
Here are a bunch more pix I took this morning while doing a bit more ruff cleaning and inspecting. my rotor slots and oil ring passages still have to be cleaned and I wana clean the outside of the irons better to prep for paint and use Itos template to open them up a bit. The tII housing Im using is gonna get media blasted and resurfaced along with another Im gonna pick up from Ito. Theses will be getting a pineapple exhuast port.
#87
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
Im waiting for paypay to transfer the money I made off my PFC and BNR turbo to my bank account, so I can get all this done and purchase my rebuild kit. Ill be in the market for a nice single when I get my taxes back and start working again
#88
Engine, Not Motor
iTrader: (1)
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 108 Likes
on
91 Posts
That is a lot of secondary port.
Just make sure to check the rotor grooves with a feeler gauge. Specs are in the Haynes. They wear into a sort of V shaped pattern. Excessive slop will wear the apex seal and rotor quickly.
Just make sure to check the rotor grooves with a feeler gauge. Specs are in the Haynes. They wear into a sort of V shaped pattern. Excessive slop will wear the apex seal and rotor quickly.
#90
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
thanks
James
#93
Engine, Not Motor
iTrader: (1)
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 108 Likes
on
91 Posts
Aaron would you say its a large port? Ito said that they were mild. I also brought him my plates he said they were fine to reuse as is and and suggested being my first rebuild to leave them be and clean up the seconaries and advised me not to spend the money on lapping and nitrating. I will be checking all clearances once I finish cleaning everything better
thanks
James
thanks
James
#94
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
My rear rotor bearing started to walk and I had some sort of oil issue to the bearings. They were all copper.
John at goopy said its a good thing I blew it before the bearing completely **** out because I'd be in it for alot more.
Everything happens for a reason
I believe the engine blew do to a walking CAS, I found the bolt loose upon disassembly.
According to Ito you will not break a seal the way I did due to a lean issue only a timing. So ruled out a fuel failure.
I will still be testing all of my fuel components.
James
John at goopy said its a good thing I blew it before the bearing completely **** out because I'd be in it for alot more.
Everything happens for a reason
I believe the engine blew do to a walking CAS, I found the bolt loose upon disassembly.
According to Ito you will not break a seal the way I did due to a lean issue only a timing. So ruled out a fuel failure.
I will still be testing all of my fuel components.
James
#95
brap brap brap
iTrader: (7)
well checked out the RA site i think im gonna buy their overhual kit and upgrade the seals and springs and the omp adaptor im pretty sure these guys prices are one of the lowest
what the deal with the thermal pellet is it a good upgrade?
arghx thanks for that site lots of great stuff on there im pretty sure my housings are in good condition bieing i have 100+ pis on the one face if not ill bring them to goopy for resurfacing hes not too far
also looking in to this
http://cgi.ebay.com/ebaymotors/Knock...Q5fCarQ5fParts
what the deal with the thermal pellet is it a good upgrade?
arghx thanks for that site lots of great stuff on there im pretty sure my housings are in good condition bieing i have 100+ pis on the one face if not ill bring them to goopy for resurfacing hes not too far
also looking in to this
http://cgi.ebay.com/ebaymotors/Knock...Q5fCarQ5fParts
http://www.youtube.com/watch?v=xDOdxEqevw4
http://www.youtube.com/watch?v=aZkZR-JBr_E
just had to adjust the sensitivity of it higher
Thread
Thread Starter
Forum
Replies
Last Post