Post your Retro-fit HID setup
02-08-09, 09:31 PM
#102
Banned. I got OWNED!!!
Join Date: Jun 2008
Location: usa
Posts: 329
Likes: 0
Received 0 Likes
on
0 Posts
........ special 
or just 
02-09-09, 10:43 AM
#104
Full Member
Join Date: Sep 2008
Location: carteret nj
Posts: 235
Likes: 0
Received 0 Likes
on
0 Posts
**** i am having a lots of problem with mine
retro fit is done i putthe projectors closest to glass possibel but still its not fitting
fx projectors are jut too big i need to cut inside the housing to fit them
retro fit is done i putthe projectors closest to glass possibel but still its not fitting
fx projectors are jut too big i need to cut inside the housing to fit them
02-10-09, 08:39 AM
#108
Looks good so far. That's really all I was planning on doing. Can you post better pics of how you attached the projector to the housing itself. I was planning on adding a sheet of ABS to the back of the housing and mounting the projector onto the added sheet so it was level. I like the black housings though, that should make it look pretty good.
Post a link to the new thread when you make it. My projectors should be here today or tomorrow, then we can see the difference between the FX and TSX projectors.
Post a link to the new thread when you make it. My projectors should be here today or tomorrow, then we can see the difference between the FX and TSX projectors.
02-10-09, 09:17 AM
#109
Gone Darkside
iTrader: (14)
Join Date: Mar 2001
Location: Irmo, SC USA
Posts: 2,569
Likes: 0
Received 0 Likes
on
0 Posts
Anyone know of some low beam projectors that are SHORT and 4" round? I'm looking to refit my East Bears but unless I want to do some metal cutting, I need them to be pretty shallow.
02-10-09, 02:06 PM
#110
There were no survivors
02-10-09, 06:40 PM
#112
Full Member
Join Date: Sep 2008
Location: carteret nj
Posts: 235
Likes: 0
Received 0 Likes
on
0 Posts
lol no i am not doing one again. But yea i ll post a writing with all pictures when i am all done cause i am still changing couple of thigs to fit it inside so i dont wanna give any wrong ideas
no its actually not that bad of a headlight for a retro fit its a clear glass
lol i wont normally use it thoug projector on it just a bent glass and light output is so crappy
because my projectors were lot bigger in diameter than other ones only thing i had to do was just cut it on right spot where circle projector part fits in and i did a jb wel around it and inside.
I am about to paint inside all black again cause jb wel looks so bad inside
lol i wont normally use it thoug projector on it just a bent glass and light output is so crappy
Looks good so far. That's really all I was planning on doing. Can you post better pics of how you attached the projector to the housing itself. I was planning on adding a sheet of ABS to the back of the housing and mounting the projector onto the added sheet so it was level. I like the black housings though, that should make it look pretty good.
Post a link to the new thread when you make it. My projectors should be here today or tomorrow, then we can see the difference between the FX and TSX projectors.
Post a link to the new thread when you make it. My projectors should be here today or tomorrow, then we can see the difference between the FX and TSX projectors.
I am about to paint inside all black again cause jb wel looks so bad inside
02-11-09, 07:53 AM
#114
Full Member
Join Date: Sep 2008
Location: carteret nj
Posts: 235
Likes: 0
Received 0 Likes
on
0 Posts
https://www.rx7club.com/2nd-generation-specific-1986-1992-17/fc3s-bixenon-retrofit-819219/#post8957438
this is the new link to my thread got some problem with nw pictures i am gonna load them again when i get back home tonight
this is the new link to my thread got some problem with nw pictures i am gonna load them again when i get back home tonight
02-11-09, 09:54 AM
#115
Banned. I got OWNED!!!
Join Date: Jun 2008
Location: usa
Posts: 329
Likes: 0
Received 0 Likes
on
0 Posts
02-11-09, 04:44 PM
#116
I just got my projectors in today, FedEx screwed up but overnighted them last night to make it up. I got the TSX projector housings, 4300K bulbs and D2S to AMP connectors so I can retain my current ballasts.
I should get around to hacking up my old 7x6's this weekend.
I should get around to hacking up my old 7x6's this weekend.
02-12-09, 07:51 AM
#121
Some HID projector units (BIXENON) use a small motor to move the shield and change the cutoff for low and high beam - the TL is like this. Some systems have an extra halogen bulb for high beam right next to the HID lamp. However, I am going to lose my high beam because the TSX is a single low beam projector.
Yes the NSX lights are cool but they are hard to find last time I looked compared to H6054 housings.
Yes the NSX lights are cool but they are hard to find last time I looked compared to H6054 housings.
02-12-09, 06:04 PM
#123
I just got my projectors in today, FedEx screwed up but overnighted them last night to make it up. I got the TSX projector housings, 4300K bulbs and D2S to AMP connectors so I can retain my current ballasts.
I should get around to hacking up my old 7x6's this weekend.
I should get around to hacking up my old 7x6's this weekend.
02-12-09, 07:06 PM
#125
Full Member
Join Date: Sep 2008
Location: carteret nj
Posts: 235
Likes: 0
Received 0 Likes
on
0 Posts
they shouldnt cause u ll be only lighting up the road not ike the pnp kits that lights up everything
As long as u adjusted right ur beam shoudnt pass over other cars hood
As long as u adjusted right ur beam shoudnt pass over other cars hood