1991rx7vert

please I need feed back I want to change the wheels but don't want it to look ghetto ...and I still want it too look like a stock sleeper...next up the suspension...

RX_Spec

iTrader: (2)

I would get some 17" wheels with close the same type spoke, painted or some silver but not chrome. That's just me though...

Rob XX 7

iTrader: (8)

im partial to mesh, either 17" or 18"

RRTEC

iTrader: (13)

mesh 17's..

Napsterfreak15

Before getting wheels I would make a Cold are intake and get a filter. The stock plastic intake tubing is not very efficient.

Also how is your engine temp? Do you still have AC?

1991rx7vert

I'm in the process of making an intake out of extra inter cooler pipe and two k&n's...engine temp is always consistent Always fixed at 1/2 way...the next time I hook up my haltech to the laptop I will tell you the exact temp...I have 2 maradyne 1250cfm fans...I removed the AC...yeah bad move ...I removed it because the 13b did not fit the mounting brackets on the 13b-re engine...I'm going to install the original 13b-re compressor back on ....yeah another bad move removing the power steering...the alcohol injection is the **** also...

Hypertek

iTrader: (3)

Get some suspension goodies..

Im not a fan of all HP with no handling upgrades.
You wont be dissapointed =D
I think BBS LM will be great
http://www.rbwheels.com/index.php?ma...405984b5875a18
or any upsized BBS wheels, nice and classy
http://www.rbwheels.com/index.php?ma...405984b5875a18
http://www.rbwheels.com/index.php?ma...405984b5875a18

1991rx7vert

yeah right after i take a second mortgage to pay for those!!!!!

cosmo7

iTrader: (3)

Mesh wheels r so dope

calicrewchief

iTrader: (2)

Get some BBS RS's. Next to a FB your driving a great sleeper.

Napsterfreak15

[QUOTE=1991rx7vert;9336206]I'm in the process of making an intake out of extra inter cooler pipe and two k&n's...engine temp is always consistent Always fixed at 1/2 way...the next time I hook up my haltech to the laptop I will tell you the exact temp...I have 2 maradyne 1250cfm fans...I removed the AC...yeah bad move ...I removed it because the 13b did not fit the mounting brackets on the 13b-re engine...I'm going to install the original 13b-re compressor back on ....yeah another bad move removing the power steering...the alcohol injection is the **** also...

Alright well you sound like you know whats going then. I just thought I would be the one to point all that out.


I watched my temp via my microtech software after I fabbed up a metal undertray and my temps went down from around 87 to around 84. Its kind of comforting seeing your exact temp. I have a front mount right now that I'm kind of hesitant to install because I'm worried about my engine heating. After I do install though it would be bad *** to get an alchi/water injector sys

cyberknetics5

i lke the older models too... but i got a 2nd generation... wish i could drive a older model... well anyone have any pictures of a nice clean stock 2nd gen... please post i havn;t seen one thats super clean ... or send me some... well just saying wussup nice pictures

1991rx7vert

Napsterfreak15...you should get the alcoholinjectionsystems.com kit...its what I got...its complete and very affordable....works great I love watching the led light after hitting 8psi...while I'm blowing past that slow *** EVO while in third gear!!!!

need RX7

iTrader: (4)

Nice! 13B-RE swaps make my pants fit funny I think some BBS RS's would look real good on there. It also needs some suspension to make it a bit lower and balance out the new-found power.

shika805

iTrader: (1)

check sig....

1991rx7vert

yeah I'm trying to decide if I should go with (option 1)- tokico blues struts and ground controls or eibachsprings, with godspeed sway barts or (option 2)- tokico's and racing beat convertible springs, and racing beat sway bars(front and rear)...the racing beat package will run me about $480 (shipped+ 269 w/tokico blues) which is about 80 bucks more that option 1

1991rx7vert

Signature test

Rob XX 7

iTrader: (8)

go with the coupe racing beats, the vert springs do not lower the car enough

hurleysurf24

iTrader: (3)

Also partial to some hot mesh. heres how it woudl look on your car (we had the same ones) .. fyi this is the only set i know in existence so no i dont know where you can get them lol.

whitena

^^Beautiful car w/ beautiful rims, I see a fmic - propbably a kickass rotary as well