FD + 20B = project
#77
dorito powered
iTrader: (5)
Join Date: Mar 2008
Location: Lincoln, NE
Posts: 2,839
Likes: 0
Received 0 Likes
on
0 Posts
that rotor graphic is BA! mind sending me a shrunk down version? I'd like to rock it on my window, I'll probably play around with it a little bit too. She's gonna look MEAN when you're done.
#78
On flats
iTrader: (29)
Join Date: Oct 2004
Location: Albuquerque
Posts: 1,379
Likes: 0
Received 0 Likes
on
0 Posts
He has the plenum because this is to be a boosted engine.
To answer your question regarding your setup with my $0.02, you should definitely have an intake. You want as close to ambient air as possible entering your engine. Anything drawn from the engine bay will hurt your performance compared to ambient air no matter what.
To answer your question regarding your setup with my $0.02, you should definitely have an intake. You want as close to ambient air as possible entering your engine. Anything drawn from the engine bay will hurt your performance compared to ambient air no matter what.
#81
Senior Member
Thread Starter
Join Date: Feb 2007
Location: Surrey, England
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
No its not internal its external. Pics just don't show it installed yet. Took a while to figure out where i could fit the thingin!
#83
Chewing on Tarantula
Join Date: May 2008
Location: Canada
Posts: 131
Likes: 0
Received 0 Likes
on
0 Posts
Hopefully you can keep it close to the turbo. Mine ended up a ways back and was boost creeping with a 50mil gate. Luckily there was enough room to swap a 60mil in the same spot and it did the trick. Cars looking really good too..
#87
Senior Member
Thread Starter
Join Date: Feb 2007
Location: Surrey, England
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
Cheers for the comments guys. Its ground to a halt at the moment. Too many customer things going on.
Also still considering what size throttle body to use. 80-90-100mm??? think as this is a track not drag car the 100mm will be too big. 90mm seems to be a common size used. However a good quality 80mm body will flow over 700hp. may be try a few see what gets best results.
Also still considering what size throttle body to use. 80-90-100mm??? think as this is a track not drag car the 100mm will be too big. 90mm seems to be a common size used. However a good quality 80mm body will flow over 700hp. may be try a few see what gets best results.
#89
Senior Member
Thread Starter
Join Date: Feb 2007
Location: Surrey, England
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
Not much progress people i must apologies. Same she on hold at the moment.
Still waiting for new arches to turn up. Will be messing around with some ground effect aero bits in the near future. Oh and buiding the engine!!!
Still waiting for new arches to turn up. Will be messing around with some ground effect aero bits in the near future. Oh and buiding the engine!!!
#93
Senior Member
Thread Starter
Join Date: Feb 2007
Location: Surrey, England
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
Cheers for the comments people,
Work on the fuel cell
I got a diffuser through today. No brakets tho same but it was a bargin so wohoo!!
Anyway i made it sit a little lower that it would usually.
I'll be finishing the exhaust in the next few days. The turbo has gone off for inspection today possiblely a change on the rear turbine housing. Info to follow.
Finalised the exhaust system now to suite the ground effects
New mid section:
Work on the fuel cell
I got a diffuser through today. No brakets tho same but it was a bargin so wohoo!!
Anyway i made it sit a little lower that it would usually.
I'll be finishing the exhaust in the next few days. The turbo has gone off for inspection today possiblely a change on the rear turbine housing. Info to follow.
Finalised the exhaust system now to suite the ground effects
New mid section:
#99
Senior Member
Thread Starter
Join Date: Feb 2007
Location: Surrey, England
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
Few modded bits: not much im affraid,
Shortened lower inlet so the bonnet nowcloses!
Modded stock 20B rails for bigger lines
Engine shift
before
After
Ports compaered to stock
Another of the exhaust almost completed
Shortened lower inlet so the bonnet nowcloses!
Modded stock 20B rails for bigger lines
Engine shift
before
After
Ports compaered to stock
Another of the exhaust almost completed