Master! Master! What's the bore that I've been after? (Master Brake Cylinder)
#1
Damn, it did start!
Thread Starter
Master! Master! What's the bore that I've been after? (Master Brake Cylinder)
Our brothers in arms in the MX5 and FD3S, to some extent the FC guys also, have a few forum threads that cover going from a 7/8 (NA Miata) to a 15/16 or a 1". or the FDs going to a 1" 929 master cylinder. Some have added bigger aftermarket brakes, others prefer the firmer action they get when going with a larger bore. In my reading I have not found anyone who regrets this change. I am considering changing my brake booster to a dual diaphragm (8.75") and 15/16 or 1" master cylinder. The braking system is a GSL-SE and can see myself trying the 15/16 first. I'm kinda surprised why this isn't a common discussion in our first gen group. Any opinions out there?
#3
Damn, it did start!
Thread Starter
I have all the SE hardlines, but am considering haven new made so I can go DOT5.
#5
Damn, it did start!
Thread Starter
#6
Out In the Barn
iTrader: (9)
One of the first disadvantages of silicone brake fluid is compressibility. You don’t want any compressibility in your braking system. This will cause your brake pedal to feel soft when you press it. Silicon brake fluid is slightly compressible and will cause this softer pedal more than glycol based fluids.
Moisture
All braking systems have moisture in them. Other types of fluid absorb water easily. Unfortunately, silicone brake fluid does not absorb water. Since the water does not mix with the fluid, it will descend to the lowest point and form a puddle. This can lead to corrosion in your hydraulic system and may impair the functioning of your brakes.
Compatibility
Another disadvantage of silicone brake fluid is that it is incompatible with glycol-based fluids. This means that you will not be able to mix the two types. If your car has used glycol-based fluids for a long time, you will have to flush and reseal the entire system to use silicone brake fluid.
Anti-lock Brakes
Silicone brake fluid also can’t be used with many anti-lock braking systems. Most systems are designed to work with glycol-based fluid. If you use silicone brake fluid instead, it may interfere with the mechanical valving found in some anti-lock braking systems.
Sealing
One of the final disadvantages of silicone brake fluid is sealing. Glycol-based fluids are easier to seal because they can’t pass through small pores in the system. Silicone brake fluid will pass through smaller pores in seals and gaskets. Therefore, it is much harder to seal effectively.
The following 2 users liked this post by KansasCityREPU:
diabolical1 (10-14-18),
Toruki (08-17-18)
#7
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,835
Received 2,603 Likes
on
1,847 Posts
Our brothers in arms in the MX5 and FD3S, to some extent the FC guys also, have a few forum threads that cover going from a 7/8 (NA Miata) to a 15/16 or a 1". or the FDs going to a 1" 929 master cylinder. Some have added bigger aftermarket brakes, others prefer the firmer action they get when going with a larger bore. In my reading I have not found anyone who regrets this change. I am considering changing my brake booster to a dual diaphragm (8.75") and 15/16 or 1" master cylinder. The braking system is a GSL-SE and can see myself trying the 15/16 first. I'm kinda surprised why this isn't a common discussion in our first gen group. Any opinions out there?
the FB master has a different bolt pattern than the FC, and FD is also different again. however the booster to firewall bolt pattern seems to be some standard, as basically every car uses it.
in the FC world, Clokker uses Subaru master/booster combos, the masters come in a bunch of sizes.
Last edited by j9fd3s; 08-18-18 at 11:01 AM.
Trending Topics
#8
ancient wizard...
GSL=SE have best brakes of all 1st gens. With the exception of track duty,properly maintained oe brakes are more than adequate. Pedal feel is not an issue,modulation/feel can be improved by addition of Braided stainless lines. Switch from DOT3 to DOT4 fluid is a further upgrade.
#10
Damn, it did start!
Thread Starter
So since it makes sense to use a GSL-SE master cylinder, does anyone suggest getting brake booster from an SE or stay with my SA?
#12
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,835
Received 2,603 Likes
on
1,847 Posts
#16
Damn, it did start!
Thread Starter
What exactly is the difference in brake boosters? As far as I can tell the SA and FB look the same with the vertical master cylinder.
#19
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,835
Received 2,603 Likes
on
1,847 Posts
#21
www.AusRotary.com
A+ on the topic heading! It got me to open it.
Yes, many people here in Australia go for the Nissan Patrol master cylinder. I'm not sure whether this is the same mode name and part number in the US, as sometimes the brake lines are swapped to the other side between LHD and RHD models. Some minor modifications are needed to fit to RX-7s, which are documented on AusRotary.com.
On our cars, you can fit the entire FD brake booster and master on an 84-85 model as a bolt on conversion, bbut not earlier as the clutch master cylinder is positioned much closer to the brake booster. The FD has the 15/16" master cylinder and the booster is a twin diaphragm model. The later series 7 and 8 boosters have a much more compact design. Fitting a FD booster opens up a whole range of options, as you can fit the 1" 929 master etc.
Personally, I don't see the need for a bigger diameter master cylinder unless you are fitting much bigger piston calipers. Even the Mazda 4 piston calipers from the FC and FD will work very well with a 7/8" master. While increasing the master cylinder size will reduce pedal stroke, it will also increase pedal effort.
The other factor to consider is that newer master cylinders, like the ones from the series 5 and FD, or the 1" masters from the 929, are made of aluminium. These are more expensive to purchase and generally cannot be rebuilt once the bore is pitted. The old trusty steel ones can be easily resleeved and rebuilt quite economically - for a lot less than a cost of a new aluminium one.
Yes, many people here in Australia go for the Nissan Patrol master cylinder. I'm not sure whether this is the same mode name and part number in the US, as sometimes the brake lines are swapped to the other side between LHD and RHD models. Some minor modifications are needed to fit to RX-7s, which are documented on AusRotary.com.
On our cars, you can fit the entire FD brake booster and master on an 84-85 model as a bolt on conversion, bbut not earlier as the clutch master cylinder is positioned much closer to the brake booster. The FD has the 15/16" master cylinder and the booster is a twin diaphragm model. The later series 7 and 8 boosters have a much more compact design. Fitting a FD booster opens up a whole range of options, as you can fit the 1" 929 master etc.
Personally, I don't see the need for a bigger diameter master cylinder unless you are fitting much bigger piston calipers. Even the Mazda 4 piston calipers from the FC and FD will work very well with a 7/8" master. While increasing the master cylinder size will reduce pedal stroke, it will also increase pedal effort.
The other factor to consider is that newer master cylinders, like the ones from the series 5 and FD, or the 1" masters from the 929, are made of aluminium. These are more expensive to purchase and generally cannot be rebuilt once the bore is pitted. The old trusty steel ones can be easily resleeved and rebuilt quite economically - for a lot less than a cost of a new aluminium one.
#23
Damn, it did start!
Thread Starter
Could someone have a 7/8" MC bored to a 15/16" and use a rebuild kit from a FD or such?
#24
www.AusRotary.com
Yes I believe a small increase like that is possible, but it will depend on whether brake specialists your way offer the service. About 10 years ago, I had my whole master resleeved and rebuilt by a local brake shop, as the genuine master cylinder was over $600 here. The resleeve involved machining out the housing and installing a new stainless steel sleeve. I had the option of increasing internal diameter when doing this, and presumably they were going to fit a bigger diameter seal kit to suit. I doubt the FD kit would be suitable, but I'm sure a brake place would be able to supply parts to suit.
#25
Rotary Freak
iTrader: (1)
. . . Personally, I don't see the need for a bigger diameter master cylinder unless you are fitting much bigger piston calipers. Even the Mazda 4 piston calipers from the FC and FD will work very well with a 7/8" master. While increasing the master cylinder size will reduce pedal stroke, it will also increase pedal effort . . .
Brake feel is subjective, and I'm probably spoiled by my other 2 cars, which have very firm, immediate pedals. YMMV