MunMun

I had someone smash my drivers side fender and I can’t seem to find any that look like they’re in good quality and don’t cost an arm and a leg can anyone point me in the right direction?

Maxwedge

iTrader: (1)

Go on the classifieds section here and look for someone parting out a car. Or post a wanted ad.

Or go on epay. Always junkyards parting out rx7's there.

j9fd3s

iTrader: (3)

buy new ones, FA01-52-211D for the left and FA01-52-111D for the right, Mazda has plenty, and they are cheap

Maxwedge

iTrader: (1)

I didn't know they were still available; That's good to know.

MunMun

do I have to go to a dealership or is there a website I can order them on

Richard Miller

For something like fenders I would go to your nearest Mazda dealer if you are buying new. The fenders would be shipped to the dealer and in turn would be shipped to you. with you footing the bill from the dealer to your home. Seems the cheapest way would be to pick up at the dealer. A quick search has the fenders from the dealer at about $120-140.

MunMun

oh damn that’s so cheap that you guys so much you’ve all been a huge help

j9fd3s

iTrader: (3)

i bought 2 of the last three last year, and then they got 14 more, so it looks like these are still being made, which seems pretty incredible. boxes are fresh too

MunMun

So I just checked all my local dealerships for Mazda and scrap yards and no one has access to oem fenders does anyone know if the fiberglass ones are any good?

derSchwamm

iTrader: (1)

I got one for about $150 delivered straight to my local mazda dealer 2 years ago. That's a steal. It's possible it's gone out of stock since but I'd call a few dealers and give the exact part number

Edit: I see some listed as available, such as at Jim Ellis Mazda (they sell online a lot). Due to shipping cost I highly recommend pickup at your local dealer. Just call them and order it

Frogman

FB fenders have never been hard to get, SA fenders are in fact NLA and cost an arm and a leg. Some on here sold two new ones 3 years ago, they fell into my hands 175$ more expensive and 500 miles away from where he was. this leads me to believe not only are they NLA but incredibly rare unless you take them off a SA . IF you need a right side fender PM me.

mustanghammer

iTrader: (3)

Just Googled the part numbers and got several listings.
https://www.tascaparts.com/oem-parts...-lh-fa0152211d

raven12aFB

tascaparts.com got them for $125.00 each....

Ckforker

Tasca is a great place for parts. I use them for my F150. They have good prices on many things.

j9fd3s

iTrader: (3)

you need to give them the part number, and they will need to order it. the catalog they have only goes back to 1986...

yeti

iTrader: (1)

I wonder if anyone could be bothered to make some fiberglass molds of SA fenders? I'd be down for a set for incidentals.

Maxwedge

iTrader: (1)

While they're at it ask them to make me a fiberglass hood.

yeti

iTrader: (1)

I have found hoods.. don't know anything about quality or anything like that..

https://www.rotaryengineeringsb.com/...t-fb-race-hood

And apparently there are duraflex ones and I believe another one but it may also be duraflex. The one above is what I've had my eye on.

Maxwedge

iTrader: (1)

Thank you Yeti! I looked for a year and could only find Mariah which was closed due to his passing (RIP) and some Aussie makers (shipping $$$).

Looks like these guys bought the rights to the Mariah stuff. Thanks again.

yeti

iTrader: (1)

If you get one I'd love to get a review on it. I don't really need one but my hood does have the rust bubbles from the glue. I'm sure it'd probably be near a wash repairing vs replacing with fibreglass. I do have the hood prop that is on the right side and in the hood so I'd need to modify it.. so maybe not so much a wash afterall.

hawk 7

iTrader: (2)

Where are you located?