S1 front lower control arms, Help! Lol
#1
Newbie
Thread Starter
S1 front lower control arms, Help! Lol
Was wondering if there is any guru on here that can confirm S1 front lower control arms will fit a 79 mazda 626 sedan?
done a bit of research (google) and they look exactly the same and seem logical that it would fit perfect
any help is appreciated
done a bit of research (google) and they look exactly the same and seem logical that it would fit perfect
any help is appreciated
Last edited by Mazdaboydownunder; 01-07-22 at 05:33 AM.
#2
Have RX-7, will restore
iTrader: (91)
I can't say with certainty that it will fit but it does look close. The differences I see are the sway bar end link mount shape and the thickness of the end of the control arm where the ball joint presses in. Another area of concern is the angle of the control arm at the ball joint end. In the picture it appears that the 626 control arm is angled farther up than the RX-7 control arm. It may just be the picture but thats what I am seeing.
The following users liked this post:
Mazdaboydownunder (01-07-22)
#3
Waffles - hmmm good
iTrader: (1)
You would need to see what the part number of the 626 would be. If its the same as the rx7 then you are golden but not sure if it would be the same. The mazda OEM part number is 8871-49-310 and 320 for the right.
Maybe @j9fd3s can help?
Maybe @j9fd3s can help?
#4
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,816
Received 2,586 Likes
on
1,837 Posts
the 626 was 8173-49-310 and 8173-49-320, so they are different, but how much is the question.
its too old my gizmo doesn't really have any information on aftermarket stuff
its too old my gizmo doesn't really have any information on aftermarket stuff
The following users liked this post:
Mazdaboydownunder (03-04-23)
#6
I know this is a old thread but I went for it and I can confirm they are the identical except for a clip on the top passenger side 626 control arm that can be cut off if necessary. Both of the new control arms were sold as 626 control arms and the old ones are out of my FB.
The following 2 users liked this post by WRXRX7:
gracer7-rx7 (03-07-23),
Mazdaboydownunder (03-04-23)
#9
QUOTE=KansasCityREPU;12551474]Looks like the 626 might be a little bit shorter.[/QUOTE]
Maybe the angle I took the photo at or something? I also thought so to but they measure the same length and width as the stock control arms. Distance between the bushings also measures the same.. Mazdaboydownunder has already used them on his vehicle apparently. These will be going on this week.
Maybe the angle I took the photo at or something? I also thought so to but they measure the same length and width as the stock control arms. Distance between the bushings also measures the same.. Mazdaboydownunder has already used them on his vehicle apparently. These will be going on this week.
Last edited by WRXRX7; 03-04-23 at 09:30 PM.
#10
needs more track time
iTrader: (16)
I wonder if the balljoint might be slightly different which would cause the part number to be different. In some old thread I remember reading about using a 626 bj to facilitate some odd sway - like maybe using FC uprights or roll center correction or something
Thread
Thread Starter
Forum
Replies
Last Post
CartieTheTranscendent
2nd Generation Specific (1986-1992)
3
03-03-20 09:28 PM