*** 1st Gen 1/4 Mile Leader Board ***
#176
Full Member
Join Date: Mar 2001
Location: Omaha, NE USA
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
I have a new 1/8 mile time. 9.03@77mph with a 2.1 60'. Sounds like my car and peejay would be a really good race. I ran that time on the stock gears though. Since then I have put the GSL-SE 4.08 gears in. Hoping that will make the difference. I really wish there was a 1/4mile track close by. I dont even know if Ill be able to make it back to the 1/8 this year.
Good NA run though peejay. Its nice to see another NA out there that will probably break into the 13s for sure with some traction.
Good NA run though peejay. Its nice to see another NA out there that will probably break into the 13s for sure with some traction.
#177
Old [Sch|F]ool
13s will be in the bag as soon as I ditch the throttle body. I have seen as low as 85KPa at full throttle and high RPM. That's roughly 3-4" of vacuum! Atmosphere is normally 95KPa here.
Ideally I'd like an IPRA style intake manifold, but I will "settle" for a Holley 750-based throttle body with a suitably ported Holley style manifold. For now, I have a 75mm throttle body setup in the works, but first I must upgrade the fuel injectors. And buy some green Rolocs so I can finish cleaning up the plenum.
Oh and I killed another rearend.
#178
Rotary Enthusiast
iTrader: (8)
Join Date: Mar 2004
Location: Ontario
Posts: 1,036
Likes: 0
Received 0 Likes
on
0 Posts
well i might as well post my new times.
Reaction ---+.5310
60Ft---------2.2001
330FT-------6.0567
Et@594-----8.6378
1/8-----------9.2018
1/8MPH-----79.78
1/4----------14.0222
1/4 MPH-----101.27
no traction in 1st and second.
mods:street ported 13BTII stock ecu, no tps, no o2 sensor. 6 psi boost. 3" exhaust.
going to install an ms in a few weeks hope things work out better
Reaction ---+.5310
60Ft---------2.2001
330FT-------6.0567
Et@594-----8.6378
1/8-----------9.2018
1/8MPH-----79.78
1/4----------14.0222
1/4 MPH-----101.27
no traction in 1st and second.
mods:street ported 13BTII stock ecu, no tps, no o2 sensor. 6 psi boost. 3" exhaust.
going to install an ms in a few weeks hope things work out better
#181
A unique monter of a engine! The rotary....
SWEET! MY BEST TIME IN MY 12A WAS 8.1557 IN THE 1/8 MILE WILL POST 1/4 MILE WHEN I BRAKE THIS NEW REBUILT IN! CHECK THESE ROTARYS OUT WORLDS FASTEST ENJOY..... 12A 13B 20B BEAST OUT! http://www.youtube.com/watch?v=n0Ab4ABB9Fw http://www.youtube.com/watch?v=O1ZStKvjVTk 13B http://www.youtube.com/watch?v=cGkgEBXZLoM
#182
finally took the car the track on drag radials, 85 gsl-se 13b turbo
reaction... .058
60'... 1.953
330... 5.400
660... 8.196
mph... 90.37
1000... 10.607
1320...12.637
mph... 113.52
reaction... .058
60'... 1.953
330... 5.400
660... 8.196
mph... 90.37
1000... 10.607
1320...12.637
mph... 113.52
#186
SAE Junkie
iTrader: (2)
I went again last week.
On this first run I left the line at 2000rpm riding clutch and fed it throttle, normal tidy shifts and reved 4th gear to 8000+rpm as I crossed line (this rpm is above my peak power). Start didn't bog but you can see it was lazy.
60' 2.410
330' 6.160
1/8 9.096
MPH 84.00
KPH 135.19
1000' 11.576
1/4 13.645
MPH 109.20
KPH 175.74
and
On the 2nd run I left the line from 4000ish rpm riding clutch, not lots of throttle again. I didn't want a repeat incident of a snapped and twisted axle. Because the run felt so tidy I decided to flat change from 3rd to 4th gear, and then I decided I would see what happened to trap speed if I changed into 5th at end of peak power. I did the 4-5 change foot pretty much flat to floor again and still lost 3mph. Interestingly I was 1.17mph down at the 1/8th track even tho this run had a faster 60ft so I'm wondering if I hit a bad cell in tune and the car bogged.
Even in 5th gear I crossed the line at 6500rpm.
60' 2.355
330' 6.150
1/8 9.154
MPH 82.83
KPH 133.30
1000' 11.696
1/4 13.839
MPH 106.07
KPH 170.70
Both of those with no burnouts and conservative takeoffs. Mostly I wanted to see what it would trap.
Basically I realise I need either 4.1's or a taller tyre. I think I should get a better diff with 4.1's in it and worry about a slightly taller tyre when I have more HP. Seeing as the cars PB is still 13.362@103 with a 2.15sec 60ft I know I can get into the 12.99 bracket without more HP just with a stronger driveline.
Also sometimes when I'm racing (street) I bake the clutch by accident and it slips. So Really its coming back to the whole driveline needing an overhaul. 4.1 toyota hilux rear end with torsen or clutch LSD and a s5 turbo gearbox with a better clutch money I don't have at the moment
On this first run I left the line at 2000rpm riding clutch and fed it throttle, normal tidy shifts and reved 4th gear to 8000+rpm as I crossed line (this rpm is above my peak power). Start didn't bog but you can see it was lazy.
60' 2.410
330' 6.160
1/8 9.096
MPH 84.00
KPH 135.19
1000' 11.576
1/4 13.645
MPH 109.20
KPH 175.74
and
On the 2nd run I left the line from 4000ish rpm riding clutch, not lots of throttle again. I didn't want a repeat incident of a snapped and twisted axle. Because the run felt so tidy I decided to flat change from 3rd to 4th gear, and then I decided I would see what happened to trap speed if I changed into 5th at end of peak power. I did the 4-5 change foot pretty much flat to floor again and still lost 3mph. Interestingly I was 1.17mph down at the 1/8th track even tho this run had a faster 60ft so I'm wondering if I hit a bad cell in tune and the car bogged.
Even in 5th gear I crossed the line at 6500rpm.
60' 2.355
330' 6.150
1/8 9.154
MPH 82.83
KPH 133.30
1000' 11.696
1/4 13.839
MPH 106.07
KPH 170.70
Both of those with no burnouts and conservative takeoffs. Mostly I wanted to see what it would trap.
Basically I realise I need either 4.1's or a taller tyre. I think I should get a better diff with 4.1's in it and worry about a slightly taller tyre when I have more HP. Seeing as the cars PB is still 13.362@103 with a 2.15sec 60ft I know I can get into the 12.99 bracket without more HP just with a stronger driveline.
Also sometimes when I'm racing (street) I bake the clutch by accident and it slips. So Really its coming back to the whole driveline needing an overhaul. 4.1 toyota hilux rear end with torsen or clutch LSD and a s5 turbo gearbox with a better clutch money I don't have at the moment
#191
Anemic Hampster pwns
Join Date: Nov 2008
Location: bay city mi.
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
1979 sa22c 12 blowthrew carb t70 turbo 50mm waistgate 255lph fp 4309fpr large fmic aluminum custom rad and spal efan mild street port 84gsl trans and rear end on 225 50 zr 15,s ventus rs-2,s best run yest at ubly dragway in MI. 1.9179 60ft 5.4783 330 ft 7.9364 et at 594 ft 1/8 et 8.4863 1/8 mph 81.82 13.2910 1/4 et 101.96 1/4 mph lost to a 72 chevelle
on juice by .1708 but it was my best run of the nite backed it up with a 13.33 2 runs later
hope this gets me on the board o yeh and that was on 7 psi boost lol get some
on juice by .1708 but it was my best run of the nite backed it up with a 13.33 2 runs later
hope this gets me on the board o yeh and that was on 7 psi boost lol get some
#192
BUY MY PARTS!!!
iTrader: (5)
Join Date: Nov 2004
Location: Blacksburg, VA
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
I ran a 9.2 in the 1/8mile
chevy 305 TransAm T5 Tranny, GSL LSD
Hankook rs-2 225/45
That was starting in 2nd gear (no traction to be found in first) so I had a 2.58 60ft (Bogged after launch)
chevy 305 TransAm T5 Tranny, GSL LSD
Hankook rs-2 225/45
That was starting in 2nd gear (no traction to be found in first) so I had a 2.58 60ft (Bogged after launch)
#193
"your turbo source"
iTrader: (1)
Join Date: Aug 2005
Location: Birmingham, AL
Posts: 246
Likes: 0
Received 0 Likes
on
0 Posts
Hey all.
I went an 11.21 at 126.28 MPH on T67 at 19 psi. The car was sitting on 26 by 10.5 ET streets. Car has much more in it, as I was lift shifting. 10 second pass is coming soon! Had a 1.62 60 ft.
Major mods:
T67 at 19 psi
E6K
8.8 ford rear with 4.88's
REW street port
ET streets
I went an 11.21 at 126.28 MPH on T67 at 19 psi. The car was sitting on 26 by 10.5 ET streets. Car has much more in it, as I was lift shifting. 10 second pass is coming soon! Had a 1.62 60 ft.
Major mods:
T67 at 19 psi
E6K
8.8 ford rear with 4.88's
REW street port
ET streets
#199
Junior Member
Join Date: Dec 2007
Location: Ontario, Canada
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
First time out last night and I bogged it something fierce on the launch lol
R/T - 0.618
60' - 2.705
330 - 7.316
1/8 - 11.114
MPH - 66.60
1000 - 14.336
1/4 - 17.069
MPH - 82.26
85 GS, minor go fast mods include:
RB full street exhaust
Rats nest & air pump delete
GSL rear end
stock everything else
R/T - 0.618
60' - 2.705
330 - 7.316
1/8 - 11.114
MPH - 66.60
1000 - 14.336
1/4 - 17.069
MPH - 82.26
85 GS, minor go fast mods include:
RB full street exhaust
Rats nest & air pump delete
GSL rear end
stock everything else