(TURBO) TII swap into GSL-SE
#176
RX-7 Alumni
ATTN Moderators
Don't know if this is the right way to contact you.
Wanted to know if the TII swap thread could become another forum within the 1st gen forum.
Just wondering, sure would be easier to navigate through all the info as opposed to one huge thread. Also the topic sometime becomes quite varied with several lines of thought being posted.
Thanks, Scott
Wanted to know if the TII swap thread could become another forum within the 1st gen forum.
Just wondering, sure would be easier to navigate through all the info as opposed to one huge thread. Also the topic sometime becomes quite varied with several lines of thought being posted.
Thanks, Scott
#177
Well I'll chime in.
Lately I've been working on my I/C plumbing and trying to get my wastegate here so I can finish my exhaust manifold. I should be picking up my driveshaft tomorrow, hopefully it will be the right length this time (they made it 3" too short the 1st time ) I ditched the stock oil cooler in favor of one from work that I mounted a fan on. It's right under the drivers side headlight. Still have to make ducting for it but I think it will work alright.
Lately I've been working on my I/C plumbing and trying to get my wastegate here so I can finish my exhaust manifold. I should be picking up my driveshaft tomorrow, hopefully it will be the right length this time (they made it 3" too short the 1st time ) I ditched the stock oil cooler in favor of one from work that I mounted a fan on. It's right under the drivers side headlight. Still have to make ducting for it but I think it will work alright.
#179
mine is about two weeks from being on the road . yah hoo !!! what I have left, is to fit the exhust, fit the ic pipes , fuel tank and lines , clean up and tune. here are some pics
Last edited by kuhlrx7; 03-04-03 at 10:15 PM.
#180
Well, not many people really know of mine.
Whats done (in the car):
13BT 0 miles /w mild street port
Haltech E6K
TII Tranny
Custom Driveshaft
Whats almost done (Not in car yet):
Haltech wiring is not complete
Radiator/IC/Oil cooler is fabed with mounts, but not bolted in.
Whats not done:
IC piping
Need to buy new turbo
I sold off my TO4E and manifold because i am going to buy a GT35/40.. But i need to save up some money 1st. I would have been done, but i owed 3K in taxes.
Here are some old pics:
http://z.gmk2.com/pics/rx7/
Whats done (in the car):
13BT 0 miles /w mild street port
Haltech E6K
TII Tranny
Custom Driveshaft
Whats almost done (Not in car yet):
Haltech wiring is not complete
Radiator/IC/Oil cooler is fabed with mounts, but not bolted in.
Whats not done:
IC piping
Need to buy new turbo
I sold off my TO4E and manifold because i am going to buy a GT35/40.. But i need to save up some money 1st. I would have been done, but i owed 3K in taxes.
Here are some old pics:
http://z.gmk2.com/pics/rx7/
#181
Senior Member
Join Date: Jan 2003
Location: Mosport Raceway,Bowmanville,Ont.
Posts: 448
Likes: 0
Received 0 Likes
on
0 Posts
Im just messin with ya. It actually reminds me of my turbo SE, anyways really nice job can't wait to here more keep me posted. What specs are ur turbo it looks like areally big TO4E, mine is .70,1.00 A/R whats yours?
seeya
RISKY7
seeya
RISKY7
#182
RX-7 Alumni
Nice job zyounker
Hey zyounker, I think it looks pretty good. Thanks for putting the pictures up. Allways nice to see someone else's project.
That turbo looks pretty big, does it fit ok. I've heard the engine can move alot when under high torque.
Lots of people are talking about the driveshaft mods but I haven't seen any good details about what is involved.
I'd like to find a solution that uses replaceable u-joints.
Great if someone could post the details.
Scott
That turbo looks pretty big, does it fit ok. I've heard the engine can move alot when under high torque.
Lots of people are talking about the driveshaft mods but I haven't seen any good details about what is involved.
I'd like to find a solution that uses replaceable u-joints.
Great if someone could post the details.
Scott
#183
Re: Nice job zyounker
Originally posted by Rex4Life
Hey zyounker, I think it looks pretty good. Thanks for putting the pictures up. Allways nice to see someone else's project.
That turbo looks pretty big, does it fit ok. I've heard the engine can move alot when under high torque.
Lots of people are talking about the driveshaft mods but I haven't seen any good details about what is involved.
I'd like to find a solution that uses replaceable u-joints.
Great if someone could post the details.
Scott
Hey zyounker, I think it looks pretty good. Thanks for putting the pictures up. Allways nice to see someone else's project.
That turbo looks pretty big, does it fit ok. I've heard the engine can move alot when under high torque.
Lots of people are talking about the driveshaft mods but I haven't seen any good details about what is involved.
I'd like to find a solution that uses replaceable u-joints.
Great if someone could post the details.
Scott
The turbo in the pic is a TO4E P trim /w a 60-1 compressor wheel on an HKS cast manifold for a 2nd gen.
It has plenty of room really. Nut the idler arm bushing is pretty close to the manifold, so you might want to use a heat sheild..
I have decided to go with a GT35/40. On about the same setup, it has made 480RWHP @ 20psi on race gase.. And that sounds pretty good to me
As for the drive shaft, i have a shortened TII driveshaft.
that will be changing because i am going with a ford 9" in back.
As for one with replacable U joints, i would say buy the mazdatrix replacement with replaceable u-joints for a TII. and have it shortened. I think they are around ~250.
Well, thanks for the complements, it those pics it is dirty has hell, i will be blasting and painting the engine bay very soon too.
-Zach
#184
Turbine turns red
i have a blown-thru holley....after idling at about 1500 RPM for 15 minutes or so the turbine turns red...anybody knows waht's teh problem?...teh temperature on the car stays fine 'though
#186
Re: Nice job zyounker
Originally posted by Rex4Life
Lots of people are talking about the driveshaft mods but I haven't seen any good details about what is involved.
I'd like to find a solution that uses replaceable u-joints.
Great if someone could post the details.
Scott
Lots of people are talking about the driveshaft mods but I haven't seen any good details about what is involved.
I'd like to find a solution that uses replaceable u-joints.
Great if someone could post the details.
Scott
zyounker- You sure you shorten the T2 shaft instead of lengthening it? I thought the rear "pumpkin" on the FC/T2 was very long unlike the FB?
#187
Re: Re: Nice job zyounker
Originally posted by setzep
zyounker- You sure you shorten the T2 shaft instead of lengthening it? I thought the rear "pumpkin" on the FC/T2 was very long unlike the FB?
zyounker- You sure you shorten the T2 shaft instead of lengthening it? I thought the rear "pumpkin" on the FC/T2 was very long unlike the FB?
Well, as you know a shop did that part for me. I thought it was shortened, but now that i think about it you are probably right.
-Zach
#190
Collections Hold
iTrader: (5)
well, yeah I can send some pics, or post them, I have to warn you , my car is all primer and I'm not too proud of it yet, its still somewhat unfinished in some areas. Maybe I'm a perfectionist, or maybe not. The motor is in box's right now in the back hatch. The stock 12a is no longer in the car so it pretty hollow under the hood. I'll take some pics though, and you can see the "before" and then I can send some "after" in a few months. I'm new to this club, so give me a few days.
#192
I just cant wait to finish mine. It wil be a daily step-up. The call will be focused on passing smog. I live in Sacramento, where it is the strictest in the WORLD.
Plans:
-Stock S4 (complete) - mild street port
-S5 turbo
-Microtech
-Small NPR
-FPR / External fuel pump (undecided - looking for low-cost method)
'83 wide body - Glacier White / HRE wheels.
Budget $2k.
I will have pics next week end. ....cant wait.....
Plans:
-Stock S4 (complete) - mild street port
-S5 turbo
-Microtech
-Small NPR
-FPR / External fuel pump (undecided - looking for low-cost method)
'83 wide body - Glacier White / HRE wheels.
Budget $2k.
I will have pics next week end. ....cant wait.....
#194
Driven a turbo FB lately?
iTrader: (1)
Originally posted by GtoRx7
well, yeah I can send some pics, or post them, I have to warn you , my car is all primer and I'm not too proud of it yet, its still somewhat unfinished in some areas. Maybe I'm a perfectionist, or maybe not. The motor is in box's right now in the back hatch. The stock 12a is no longer in the car so it pretty hollow under the hood. I'll take some pics though, and you can see the "before" and then I can send some "after" in a few months. I'm new to this club, so give me a few days.
well, yeah I can send some pics, or post them, I have to warn you , my car is all primer and I'm not too proud of it yet, its still somewhat unfinished in some areas. Maybe I'm a perfectionist, or maybe not. The motor is in box's right now in the back hatch. The stock 12a is no longer in the car so it pretty hollow under the hood. I'll take some pics though, and you can see the "before" and then I can send some "after" in a few months. I'm new to this club, so give me a few days.
#196
smog nazi destroyer
Originally posted by jmseven
I just cant wait to finish mine. It wil be a daily step-up. The call will be focused on passing smog. I live in Sacramento, where it is the strictest in the WORLD.
Plans:
-Stock S4 (complete) - mild street port
-S5 turbo
-Microtech
-Small NPR
-FPR / External fuel pump (undecided - looking for low-cost method)
'83 wide body - Glacier White / HRE wheels.
Budget $2k.
I will have pics next week end. ....cant wait.....
I just cant wait to finish mine. It wil be a daily step-up. The call will be focused on passing smog. I live in Sacramento, where it is the strictest in the WORLD.
Plans:
-Stock S4 (complete) - mild street port
-S5 turbo
-Microtech
-Small NPR
-FPR / External fuel pump (undecided - looking for low-cost method)
'83 wide body - Glacier White / HRE wheels.
Budget $2k.
I will have pics next week end. ....cant wait.....
#197
Well im holding off on putting the engine in now b/c i found a cage cheap so ill do that first. When you guys installed your engines what route did you go on the front cover and bracket combo? I had a 12a cover and bracket but i hear ive got to modify it for the length diff of a 13b.