My stockport 401 HP pull *vid*
06-10-06, 01:52 PM
#1
My stockport 401 HP pull *vid*
Made 401.15 on my stockport 10th AE. The number required 20 PSI to make, so its pretty apparent those motors dont flow very well. VMount setup was done by Ryan Shook, and tuning was done by Trevor.
vid:
http://www.jrat.snikt.org/vid/rats401.wmv
vid:
http://www.jrat.snikt.org/vid/rats401.wmv
06-10-06, 05:44 PM
#5
Rotary Freak
Did you trap 124mph on 100 octane or 93? I'm gonna run a ported S5 engine with a bigger turbo and hopefully a little less weight than your setup, I'm just trying to gauge what I MIGHT be able to run.
Trending Topics
06-10-06, 10:01 PM
#12
multipersonality disorder
Join Date: Feb 2002
Location: so. cal
Posts: 5,656
Likes: 0
Received 0 Likes
on
0 Posts
i kept thinking those numbers were so low, but i haven't done anything with stock ports in a while. t61 is ballpark the same as a gt35r, and lots of guys hit 400whp @ 15-16 psi or so.
i'm definately not knocking you, please don't take it that way. but i'd go over the setup and just give everything a once over if it's taking that much boost on that turbo to make that power. it might be an indication that something might not be right.
what were the afr's and egt's like?
but in any case, good job on the power
i'm definately not knocking you, please don't take it that way. but i'd go over the setup and just give everything a once over if it's taking that much boost on that turbo to make that power. it might be an indication that something might not be right.
what were the afr's and egt's like?
but in any case, good job on the power
06-11-06, 03:47 AM
#16
Originally Posted by J-Rat
Oh, I am sure its the ports. The S4 motor has very small porting. I think the timing is a little off too on the retarded side. We are writing a new map now. Afrs were low 11s high 10s..
06-11-06, 09:30 AM
#18
wow way to go jrat! nice too see you hit the 400 mark! Have you run a compression test reasantly? I know you've been run the crap out of that motor and it's probably not as healthy as it could be. Maybe the reason for the slightly lower numbers? However really you gotta figure that porting can give you what 15-20% more hp so thats around 480rwhp at the same psi witch should be about right for that turbo also the higher compression from the rebuilt motor should yeild more hp as well. You guys can correct me if I'm wrong
crispeed: you've seen cars pushing 600rwhp on stock ports with a t61?? I would figure maybe that much on a t66 but I think that's just a bit too optamistic for a t61 but thats just me.
crispeed: you've seen cars pushing 600rwhp on stock ports with a t61?? I would figure maybe that much on a t66 but I think that's just a bit too optamistic for a t61 but thats just me.
Last edited by hondahater; 06-11-06 at 09:33 AM.
06-11-06, 10:36 AM
#19
Originally Posted by crispeed
I have personally not found any differences in the two types of motors everything else being equal up to about 600 rwhp. The porting is not to blame. Now if you said intake manifold differences then I would agree.
06-11-06, 01:22 PM
#23
[QUOTE=
crispeed: you've seen cars pushing 600rwhp on stock ports with a t61?? I would figure maybe that much on a t66 but I think that's just a bit too optamistic for a t61 but thats just me.[/QUOTE]
No
What I'm saying from my experience all things being eqaul stock vs stock or ported vs ported the difference in size of the port runners does not make a difference up to about 570 to 600hp. The intake manifold/TB is where the major difference would be. My 1st 600hp 13b was a S-4 TII but that was with a custom intake not the factory one. The same setup on a series 6/FD did not make any difference in power at the same boost and porting configuration.
crispeed: you've seen cars pushing 600rwhp on stock ports with a t61?? I would figure maybe that much on a t66 but I think that's just a bit too optamistic for a t61 but thats just me.[/QUOTE]
No
What I'm saying from my experience all things being eqaul stock vs stock or ported vs ported the difference in size of the port runners does not make a difference up to about 570 to 600hp. The intake manifold/TB is where the major difference would be. My 1st 600hp 13b was a S-4 TII but that was with a custom intake not the factory one. The same setup on a series 6/FD did not make any difference in power at the same boost and porting configuration.
06-11-06, 02:14 PM
#25
multipersonality disorder
Join Date: Feb 2002
Location: so. cal
Posts: 5,656
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 2a+RoN
WTF???
don't worry about him. that's the guy that claimed 300+whp on a stock turbo blowing smoke, and 30mpg. you learn to ignore claims like that.