Cheapest place to buy a garret 35/40 kit
07-31-03, 06:06 PM
#1
Full Member
Thread Starter
Join Date: Oct 2002
Location: ohio
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts
Wheres the cheapest place to buy a garret 35/40 kit
Wheres the cheapest place to buy that kit?
rx7 store shows 3900 on their website.
Unless someone thinks I should look towards a different turbo for a mostly street driven car.
rx7 store shows 3900 on their website.
Unless someone thinks I should look towards a different turbo for a mostly street driven car.
Last edited by barkeep; 07-31-03 at 06:13 PM.
07-31-03, 09:16 PM
#2
VIP - Very Irish Person
Join Date: Jan 2002
Location: NC State
Posts: 1,458
Likes: 0
Received 0 Likes
on
0 Posts
bi-state customs seem to have a pretty good deal going on a single turbo set-up. Check under the classifieds section for vendors/groupbuys.
Last edited by tookwik; 07-31-03 at 09:21 PM.
07-31-03, 11:15 PM
#3
Rotary Enthusiast
Join Date: Feb 2001
Location: In the Sky
Posts: 1,190
Likes: 0
Received 0 Likes
on
0 Posts
www.a-spectuning.com is selling there base 35/40 kit w/ manderal bent d-pipe, low rise manifold, polsihed compressor, etc... for $3500
i think the GT70R option is $400 more
i think the GT70R option is $400 more
08-11-03, 10:51 AM
#7
NorCal 7's Co-founder
Originally posted by 88fc3sw/HX83
I got a REAL turbo kit for you for $1899 shipped!! The REAL SRmotorsports stageII turbo kit. Full boost by 4250 rpm and 540 rwhp @ 19 psi.
I got a REAL turbo kit for you for $1899 shipped!! The REAL SRmotorsports stageII turbo kit. Full boost by 4250 rpm and 540 rwhp @ 19 psi.
Zach
Trending Topics
08-11-03, 12:18 PM
#8
rotary sensei
iTrader: (5)
Join Date: Mar 2001
Location: Virginia
Posts: 2,312
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by BoostedRex
While 540 rwhp does sound really nice, 4250rpm is a long time to wait for full spool when the 35/40 can get there much faster. I know it won't put down those kinds of numbers, but still. What kind of engine porting was done to the car that spooled the SR turbo at 4250?? If it was a stock or streetport then I would be willing to bet that you could spool a good bit faster with a half bp or a full out bridge port. Any info on that question?? Thanx in advance.
Zach
While 540 rwhp does sound really nice, 4250rpm is a long time to wait for full spool when the 35/40 can get there much faster. I know it won't put down those kinds of numbers, but still. What kind of engine porting was done to the car that spooled the SR turbo at 4250?? If it was a stock or streetport then I would be willing to bet that you could spool a good bit faster with a half bp or a full out bridge port. Any info on that question?? Thanx in advance.
Zach
08-11-03, 01:14 PM
#9
All Motor
iTrader: (2)
Join Date: Mar 2003
Location: Redmond, WA
Posts: 1,604
Likes: 0
Received 0 Likes
on
0 Posts
ErnieT obtained over 520RWHP at 20PSI with a stock motor and stock ignition. That turbo hits 15PSI at about 3700RPM, it spools about the same as stock twins with full 3" exhaust and intake running non-sequential. Not nearly as quick as the GT35/40, but it will make more power too.
08-12-03, 12:05 PM
#12
Full Member
Join Date: May 2002
Location: USA!
Posts: 130
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by tookwik
bi-state customs seem to have a pretty good deal going on a single turbo set-up. Check under the classifieds section for vendors/groupbuys.
bi-state customs seem to have a pretty good deal going on a single turbo set-up. Check under the classifieds section for vendors/groupbuys.
Thread
Thread Starter
Forum
Replies
Last Post
82streetracer
1st Generation Specific (1979-1985)
7
08-23-15 09:28 AM
Megasquirt timing map and EGt ?? what do you guys think
immanuel__7
Megasquirt Forum
3
08-22-15 09:34 PM
