Anyone using the $28 1680cc Injectors ?
#26
7s before paint!!!
iTrader: (2)
NAPA no longer sells the Bosch ones. The replacements are delphi IIRC. They flow the same but they are the disc type. They are also $80 a piece. Look for a ford product in the early 2000 range that is running a 4.6 or 5.4 on CNG. The difference is that CNG calls for a far greater flow rate than gasoline. My guess would be that the V8 Chryslers that run on CNG will have something close if not the same (Chrysler has used Bosch injectors for a while now).
#27
*** Bless The USA
Thread Starter
iTrader: (8)
Join Date: Jan 2007
Location: Saint Louis / Illinois
Posts: 7,139
Received 0 Likes
on
0 Posts
I've done hours of research on this. Lots of people advertise selling them but when you call to order, they're out of stock. I called BG Reman back and they're all out of stock too.
So, looks like these are being used up and no cores are available.
I found a deal on (8) new Ford 160LB injectors for $389 shipped so I'll probably do that.
So, looks like these are being used up and no cores are available.
I found a deal on (8) new Ford 160LB injectors for $389 shipped so I'll probably do that.
#31
*** Bless The USA
Thread Starter
iTrader: (8)
Join Date: Jan 2007
Location: Saint Louis / Illinois
Posts: 7,139
Received 0 Likes
on
0 Posts
Hello
did you find the injectors?
Am also looking for some injectors but not sure what size to use, learning as a go!
I was told to install 4 1,000cc, what you or the rest of the gang recommend?
Set up is a 12A freshly rebuild/street ported, other than that its all stock with EOM apex seals.
Turbo manifold with a T04 flange, size to be determine?? Help,
am in Colorado so the 7,000 altitude is a factor on the turbo selection, but I dont know!!!
I just want to build a peepy daily driver, 300HP+'s any suggestion?
Thanks,
Andres
sorry for the hijack!
did you find the injectors?
Am also looking for some injectors but not sure what size to use, learning as a go!
I was told to install 4 1,000cc, what you or the rest of the gang recommend?
Set up is a 12A freshly rebuild/street ported, other than that its all stock with EOM apex seals.
Turbo manifold with a T04 flange, size to be determine?? Help,
am in Colorado so the 7,000 altitude is a factor on the turbo selection, but I dont know!!!
I just want to build a peepy daily driver, 300HP+'s any suggestion?
Thanks,
Andres
sorry for the hijack!
They sell a 105 mm throttlebody. They also sell smaller ones too.
#33
*** Bless The USA
Thread Starter
iTrader: (8)
Join Date: Jan 2007
Location: Saint Louis / Illinois
Posts: 7,139
Received 0 Likes
on
0 Posts
#36
spending too much money..
iTrader: (2)
congrats! did you find cheap connectors? I've gotten some from summit and some from rx7.com. The summit ones took about 3months to come in witch was ok because I ordered a crap load of stuff while it was on back order and didn't have to pay handling fees each time, lol The rx7.com place was about the same price but I got them right away. Oh yeah and I used to get them from autozone and the like and hey where cheap however they have been out of stock reasantly.
#37
*** Bless The USA
Thread Starter
iTrader: (8)
Join Date: Jan 2007
Location: Saint Louis / Illinois
Posts: 7,139
Received 0 Likes
on
0 Posts
congrats! did you find cheap connectors? I've gotten some from summit and some from rx7.com. The summit ones took about 3months to come in witch was ok because I ordered a crap load of stuff while it was on back order and didn't have to pay handling fees each time, lol The rx7.com place was about the same price but I got them right away. Oh yeah and I used to get them from autozone and the like and hey where cheap however they have been out of stock reasantly.
I figured since it's a basic GM or Ford connector, it should be easy to source.
Maybe I'll try O'reilly's, Advanced or Napa.
I need to finish my turbo manifold first then I'll start the wiring nightmare
#40
Sharp Claws
iTrader: (30)
necro post but i was looking into this and the cheapo rockauto GBR pricing is just for the service of sending in your injectors to be cleaned. the pricing at the previously mentioned sites skyrocketed to $120 per injector since.
$50 1600's long gone now. you can get them for $90 brand new(from ford) still however.
$50 1600's long gone now. you can get them for $90 brand new(from ford) still however.
Last edited by RotaryEvolution; 01-19-12 at 01:55 PM.
Thread
Thread Starter
Forum
Replies
Last Post
HalifaxFD
Canadian Forum
126
05-09-16 07:06 PM